CQM6L Contrôle de fuite intégré à l'MCCB - Fabricant OEM/ODM
Le MCCB CQM6L provides overload, short circuit and adjustable earth-leakage protection within its published 16–800A range. Specification should follow the system voltage, load, conductor coordination, prospective fault current and applicable rules—not the ampere value alone.
Vue d'ensemble du produit
CQM6L is a earth leakage circuit breaker for AC 400/415V distribution and protection applications. Its published range covers 16–800A with 4P for frames 160/250; 3P/4P for frames 630/800 options. Selection depends on the complete power-system design, including fault level, coordination, conductor ampacity, enclosure conditions and local rules.
The supplied product specification references IEC/EN 60947-1, IEC/EN 60947-2, IEC/EN 60947-3 and IEC/EN 60947-4, together with GB/T 14048.1, .2, .3 and .4. These standard references do not, by themselves, establish certification for a particular order.
Principales caractéristiques
Applications typiques
Typical applications include distribution and motor circuits where an MCCB and residual-current function are specified together. These are evaluation contexts rather than universal approvals. Confirm the exact frame, voltage, breaking duty, trip unit, accessories and installation method before specification.
Demandes d’admission et guide de sélection
Use the verified CQM6L values below to create a shortlist, then validate the complete circuit. An MCCB rating does not replace conductor calculations, fault-current analysis, coordination review or local installation requirements.
| Point de sélection | CQM6L reference | Ce que le projet doit confirmer |
|---|---|---|
| Courant nominal | 16–800A | Design current, conductor ampacity, installation method, temperature and grouping |
| Tension | AC 400/415V | Supply system and equipment rating |
| Pôles | 4P for frames 160/250; 3P/4P for frames 630/800 | Live conductors and neutral treatment |
| Trip / protection | thermal-magnetic trip | Load profile, fault response and coordination |
| Capacité de rupture | Classes C/S/M/H jusqu'à 75kA, selon le châssis et la configuration commandée | Prospective short-circuit current at the installation point |
Overcurrent vs Earth-Leakage Protection
An MCCB's overcurrent function does not replace residual-current protection. Select leakage sensitivity, delay and waveform type from the verified model data and project rules.
Leakage Protection
Confirm Leakage Selection →
MCCB vs MCB
An MCCB is normally evaluated for higher current, fault duty or accessory flexibility; an MCB may be more suitable for compact final circuits.
Current & Fault Duty
Compare MCCB and MCB →
Icu vs Ics
The saved data for CQM6L lists C/S/M/H classes up to 75kA, according to frame and ordered configuration. Match the declared duty to the prospective short-circuit current and continuity objective.
Short-Circuit Study
Review Technical Support →
Pole and Neutral Arrangement
Published pole options are 4P for frames 160/250; 3P/4P for frames 630/800. Confirm which conductors must be switched, protected and isolated together.
System Arrangement
View MCCB Range →
Guide d'achat
- State the exact model: CQM6L.
- Provide frame and rated current within the published range: 16–800A.
- Confirm poles: 4P for frames 160/250; 3P/4P for frames 630/800.
- Specify the trip unit or protection function: thermal-magnetic trip.
- Provide system voltage, frequency, application, expected fault level, destination market and quantity.
- List required accessories, terminals, documents and any approved OEM/ODM marking or packaging requirements.
Examens d’installation et de coordination
- Use the exact model drawing and instructions; do not infer terminal positions, supply direction or accessory compatibility from another MCCB.
- Verify conductor material and cross-section against the circuit calculation, terminal data, temperature and grouping.
- Confirm Icu/Ics or DC fault duty, upstream/downstream coordination, enclosure conditions, altitude and clearances.
- Installation, isolation, testing and maintenance must be performed by qualified personnel under applicable rules.
Selection Guide
| Product code ① | Shell frame grade ② | Breaking capacity ③ | Operating method ④ | Number of poles ⑤ | ||||
|---|---|---|---|---|---|---|---|---|
| CQM6L | 160 | C | P | 4 | ||||
| Molded case circuit breaker | C | S | M | H | P:Motorized operation Z:Turning handle W.Direct operation |
160A:4P 250A:4P 400A:3P,4P 630A:3P,4P 800A:3P,4P |
||
| 160 | 160 | 25/18 | 35/25 | / | / | |||
| 250 | 250 | 25/18 | 35/25 | / | / | |||
| 400 | 400 | / | 35/25 | 50/35 | 75/50 | |||
| 630 | 630 | / | 35/25 | 50/35 | 75/50 | |||
| 800 | 800 | / | 35/25 | 50/35 | 75/50 | |||
| Trip Unit &Accessories ⑥ | Rated current A ⑦ | Function ⑧ | 4P Option Code ⑨ | Special code ⑩ | |
|---|---|---|---|---|---|
| 300 | 160A | 2 | A | I | |
| The first digit indicates the type of detent 2:Instantaneous detent only 3:Duplicate detent Note:The last two digits are the accessory designator (see accessory table). |
160 | 16,20,32,40,50,63,80,100,125,140,160 | 1:For power distribution 2:For motor protection |
A:N-pole is unprotected and cannot be combined B:N-pole is unprotected and can be combined C:N-pole is protected and can be combined D:N-pole is protected and cannot be combined |
I:Overload alarm non trip function |
| 250 | 100,125,140,160,180,200,225,250 | ||||
| 400 | 250,315,350,400 | ||||
| 630 | 250,315,350,400,500,630 | ||||
| 800 | 500,630,700,800 | ||||
| Product code ⑪ | Breaking capacity ⑫ | ||||||
|---|---|---|---|---|---|---|---|
| L1 | Y1 | ||||||
| Fixed delay type | Quick three-step adjustable | Fixed delay type | Quick three-step adjustable | ||||
| L1:30 | L6:200 | L11:30,50,100 | Y1:0.1S | Y4:0.4S | Y7:0.7S | Y10:1.0S | Y13:0.45,1,2 |
| L2:50 | L7:300 | L12:30,100,200 | |||||
| L3:75 | L8:500 | L13:30,100,500 | Y2:0.2S | Y5:0.5S | Y8:0.8S | Y11:1.1S | Y14:1,2,3 |
| L4:100 | L9:500 | L14:100,300,500 | |||||
| L5:150 | L10:1000 | L15:100,300,500 | Y3:0.3S | Y6:0.6S | Y9:0.9S | Y12:1.2S | |
| L16:100,300,1000 | |||||||
| Accessory Voltage ⑬ | Motorized operating voltage ⑭ | Installation ⑮ | Terminal Block Option ⑯ | |||
|---|---|---|---|---|---|---|
| Q1 | D1 | Q | 2 | |||
| Undervoltage detent Q1:AC220V Q2:AC240V Q3:AC380V Q4:AC415V | Shunt release F1:AC220V F2:AC380V F3:DC110V F4:DC24V | Auxiliary alarm J1:AC125V J2:AC250V J3:DC125V J4:DC24V | CD1 Electrical Operation D1:AC220V D2:AC230V D3:AC380V D4:AC400V | CD2 Electrical Operation D5:AC230V D6:AC110V D7:DC220 D8:DC110 D9:AC110~240V D10:DC100~220V | Q:Front of plate H:Rear of plate C:Inserted | 1:Noinstallation 2:Installation |
| Note:When motorized operation is selected,please refer to the external accessories for the two voltages applicable for motorized operation. | ||||||
Accessory List
Main Technical Parameters
| Model number | CQM6L-160 | CQM6L-250 | ||||
|---|---|---|---|---|---|---|
| Rated current of frame level Inm(A) | 160 | 250 | ||||
| Nombre de poteaux | 4 | 4 | ||||
| Rated current In(A),at 40°C,50°C,55°C | 16,20,32,40,50,63,80,100,125,160 | 100,125,140,160,180,200,225,250 | ||||
| Rated operating voltage Ue(V),AC 50/60Hz | 400/415 | 400/415 | ||||
| Rated insulation voltage Ui (V) | 800 | 800 | ||||
| Rated impulse withstand voltage Uimp(KV) | 8 | 8 | ||||
| Breaking capacity designation | C | S | C | S | ||
| Short-circuit breaking capacity Icu/Ics(kA) | AC400/415V | 25/18 | 35/25 | 25/18 | 35/25 | |
| Selectivity category | A | A | A | A | ||
| Number of operating cycles(cycle) | ON | 6000 | 6000 | |||
| OFF | 10000 | 10000 | ||||
| Trip mechanisms and protection types | Magnetic trip | Power distribution protection | ● | ● | ● | ● |
| Motor protection | ● | ● | ● | ● | ||
| Thermal-magnetic trip | Power distribution protection | ● | ● | ● | ● | |
| Motor protection | ● | ● | ● | ● | ||
| Accessory | Auxiliary contacts | ● | ● | ● | ● | |
| Alarm contacts | ● | ● | ● | ● | ||
| Shunt disconnect | ● | ● | ● | ● | ||
| Undervoltage detent | ● | ● | ● | ● | ||
| Manual operating mechanism | ● | ● | ● | ● | ||
| Motorized operating mechanism | ● | ● | ● | ● | ||
| Backplane wiring | ● | ● | ● | ● | ||
| Inserted | ● | ● | ● | ● | ||
| Coupling plate | ● | ● | ● | ● | ||
| Partition between phases | ● | ● | ● | ● | ||
| Derivative products | Dedicated for prepayment electric meters | ● | ● | ● | ● | |
| Overload alarm without trip | ● | ● | ● | ● | ||
| Overall dimensions (mm) (a-b-c-ca) |  |
3 P | 90×155×71×95 | 105×165×71×96 | ||
Note: ● indicates an available optional accessory; – indicates that the accessory is not available.
Main Technical Parameters
| Model number | CQM6L-630 | CQM6L-800 | ||||||
|---|---|---|---|---|---|---|---|---|
| Rated current of frame level Inm(A) | 630 | 800 | ||||||
| Nombre de poteaux | 3,4 | 3,4 | ||||||
| Rated current In(A),at 40°C,50°C,55°C | 250,315,350,400,500,630 | 500,630,700,800 | ||||||
| Rated operating voltage Ue(V),AC 50/60Hz | 400/415 | 400/415 | ||||||
| Rated insulation voltage Ui (V) | 800 | 800 | ||||||
| Rated impulse withstand voltage Uimp(KV) | 8 | 8 | ||||||
| Breaking capacity designation | S | M | H | S | M | H | ||
| Short-circuit breaking capacity Icu/Ics(kA) | AC400/415V | 35/25 | 50/35 | 75/50 | 35/25 | 50/35 | 75/50 | |
| Selectivity category | A | A | A | A | A | A | ||
| Number of operating cycles (cycle) |
ON | 3000 | 1000 | |||||
| OFF | 8000 | 3000 | ||||||
| Trip mechanisms and protection types | Magnetic trip | Power distribution protection | ● | ● | ● | ● | ● | ● |
| Motor protection | ● | ● | ● | ● | ● | ● | ||
| Thermal-magnetic trip | Power distribution protection | ● | ● | ● | ● | ● | ● | |
| Motor protection | ● | ● | ● | ● | ● | ● | ||
| Accessory | Auxiliary contacts | ● | ● | ● | ● | ● | ● | |
| Alarm contacts | ● | ● | ● | ● | ● | ● | ||
| Shunt disconnect | ● | ● | ● | ● | ● | ● | ||
| Undervoltage detent | ● | ● | ● | ● | ● | ● | ||
| Manual operating mechanism | ● | ● | ● | ● | ● | ● | ||
| Motorized operating mechanism | ● | ● | ● | ● | ● | ● | ||
| Backplane wiring | ● | ● | ● | ● | ● | ● | ||
| Inserted | ● | ● | ● | ● | ● | ● | ||
| Coupling plate | ● | ● | ● | ● | ● | ● | ||
| Partition between phases | ● | ● | ● | ● | ● | ● | ||
| Derivative products | Dedicated for prepayment electric meters | ● | ● | ● | ● | ● | ● | |
| Overload alarm without trip | ● | ● | ● | ● | ● | ● | ||
| Overall dimensions (mm) (a–b–c–ca) | |
3 P | 140×257×108×156 | 210×275×108×156 | ||||
| 4 P | 185×257×108×156 | 280×275×108×156 | ||||||
Note: ● indicates an available optional accessory; – indicates that the accessory is not available.
Operating Characteristics
The following table gives the inverse-time operating characteristics for distribution protection with all poles energised at an ambient temperature of +40°C, without humidity compensation.
| Test current designation | Setting current multiple | Conventional time | Initial state |
|---|---|---|---|
| In≤63 In>63 | |||
| Conventional non-tripping current | 1.05 | ≥1h ≥2h | Cool state |
| Conventional tripping current | 1.30 | <1h<2h | Hot state |
The following table gives the inverse-time operating characteristics for motor protection with all poles energised at an ambient temperature of +40°C, without humidity compensation.
| Test current designation | Setting current multiple | Conventional time | Initial state |
|---|---|---|---|
| In≤800 | |||
| Conventional non-tripping current | 1.0 | ≥2h | Cool state |
| Conventional tripping current | 1.2 | <2h | Hot state |
The operating-characteristics reference gives an instantaneous trip current setting of 10In for distribution protection. Confirm the applicable trip-unit setting for the ordered configuration.
The short-circuit current setting value of the instaneous tripper of the circuit breaker for motorprotection is 12ln
The stated accuracy of the instantaneous trip current setting is 20% of the setting value.
CQM6L-160 Operating Characteristic Curve
CQM6L-250 Operating Characteristic Curve
CQM6L-400 / 630 Operating Characteristic Curve
CQM6L-800 Operating Characteristic Curve
Outline and Installation Dimensions(mm)
| Molded case circuit breaker | Overall dimension | Installation dimensions | Boit | |||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| A | A1 | A2 | A3 | B | B1 | B2 | B3 | B5 | B6 | H | H1 | H2 | H3 | H4 | H5 | H6 | A4 | B4 | ||||||
| 3P | 4P | 3P | 4P | 3P | 4P | 3P | 4P | |||||||||||||||||
| CQM6L-160CS | 90 | 120 | 60 | 90 | – | – | – | – | 155 | 134 | 103 | 50 | 48 | – | 95 | 76 | 2.2 | 70.7 | 62.3 | 23.8 | 24.6 | 30 | 132 | M8 |
| CQM6L-250CS | 105 | 140 | 70 | 105 | – | – | – | – | 165 | 144 | 102 | 50 | 97 | – | 95.8 | 75 | 2.8 | 71 | 62.2 | 22.9 | 23.3 | 35 | 126 | M8 |
| CQM6L-400SMH | 140 | 185 | 88 | 132 | 140 | 196 | 112 | 168 | 257 | 230 | 179 | 90 | 103 | 42 | 156 | 112.1 | 3.5 | 107.5 | 99.6 | 31.4 | 32 | 44 | 194 | M10 |
| CQM6L-630SMH 400A | 140 | 185 | 88 | 132 | 140 | 196 | 112 | 168 | 257 | 230 | 179 | 90 | 103 | 42 | 156 | 112.1 | 3.5 | 107.5 | 99.6 | 31.4 | 32 | 44 | 194 | M10 |
| CQM6L-630SMH 630A | 140 | 185 | 88 | 132 | 140 | 196 | 112 | 168 | 257 | 230 | 179 | 90 | 103 | 42 | 156 | 112.1 | 3.5 | 107.5 | 99.6 | 32.4 | 34 | 44 | 194 | M10 |
| CQM6L-800SMH 630A | 210 | 280 | 140 | 210 | 180 | 250 | 140 | 210 | 275 | 243 | 192 | 90 | 103 | 87 | 156 | 112.5 | 2.7 | 107.6 | 99.8 | 25.9 | 27 | 70 | 242.5 | M12 |
| CQM6L-800SMH 800A | 210 | 280 | 140 | 210 | 180 | 250 | 140 | 210 | 275 | 243 | 192 | 90 | 103 | 87 | 156 | 112.5 | 2.7 | 107.6 | 99.8 | 27.9 | 29 | 70 | 242.5 | M12 |
Pourquoi choisir CHAC
Avec plus de 30 ans d'expérience dans la fabrication, 1100 employés et 100 millions de poteaux
Avec une capacité annuelle de 90% machines automatisées, CHAC garantit une production stable et rigoureuse.
contrôle qualité pour les clients OEM/ODM mondiaux. Notre système de fabrication interne permet une collaboration à long terme.
Coopération pour les marques électriques, les importateurs et les distributeurs.
30+
ANNÉE D'EXPÉRIENCE
Spécialisée dans la fabrication d'appareils électriques à faible tension
1100+
EMPLOYÉS
Une équipe professionnelle garantit une qualité et une livraison stables
100 millions d'euros
Capacité annuelle des poteaux
Capacité de production à grande échelle pour répondre à la demande mondiale
90%
PRODUCTION AUTOMATIQUE
Une automatisation avancée pour une efficacité et une cohérence élevées
Ligne de montage automatisée
Laboratoire d'essai
Injection et estampage
Inspection de qualité
Un système de contrôle qualité strict assure que chaque produit respecte les normes internationales.
Qu'est-ce que nous pouvons personnaliser ?
For CQM6L projects, CHAC can review private-label marking, packaging, approved appearance options, published 16–800A electrical configurations and technical-document requirements. Requests outside the published range are subject to engineering evaluation, testing, minimum order quantity and project feasibility.
Enclosure
Design
Customized enclosure sizes, structures and installation details.
Internal
Configuration
Flexible internal layout and component arrangement options.
Branding &
Logo
Private label logos, nameplates and brand identification.
Emballage
Design
Custom cartons, labels, manuals and packaging solutions.
Électrique
Configuration
Tailored electrical setup based on application requirements.
Certification
Support
Support for target-market standards and compliance requirements.
Télécharger
Disjoncteur à boîtier moulé de la série CQM6
Vue d'ensemble complète des produits pour les composants électriques à basse tension et référence de sélection de produit.
Dois-je avoir des documents techniques ?
Contactez-nous pour obtenir des fiches techniques, des certificats, des dessins, des conseils de sélection ou une assistance pour des projets OEM/ODM.
CQM6L Product FAQ
What is the CQM6L MCCB used for?
The CQM6L is specified for overload, short circuit and adjustable earth-leakage protection in AC 400/415V systems within the published 16–800A range. Suitability depends on the fault study, conductor coordination, enclosure and local rules.
How does residual-current protection work in the CQM6L?
The residual-current function monitors imbalance associated with earth leakage and trips at the selected sensitivity or delay. The waveform type, threshold, time delay, earthing arrangement and local rules must be confirmed for the exact configuration.
How do I choose the CQM6L rated current and poles?
Start with the design current and conductor calculation, then choose a published current within 16–800A and poles from 4P for frames 160/250; 3P/4P for frames 630/800. Neutral treatment, fault level, ambient conditions and coordination also need review.
What breaking capacity should I check on the CQM6L?
Use the declared C/S/M/H classes up to 75kA, according to frame and ordered configuration for the exact frame, voltage and configuration. The prospective short-circuit current at the installation point must be within the applicable duty; a larger ampere value alone is not a selection rule.
Can the CQM6L replace an MCB or an earth-leakage device?
An MCCB is not automatically a like-for-like replacement. The CQM6L provides overload, short circuit and adjustable earth-leakage protection; residual-current protection, DC interruption, adjustable settings and other functions must be confirmed separately from the project requirement.
How should the CQM6L be installed and tested?
Use only the exact model drawing, terminal identification and accessory instructions. A qualified person should verify isolation, conductor size, torque, clearances, settings, fault duty and functional tests before energising the circuit.
Confirm the Right CQM6L Configuration
Send the frame, rated current, poles, protection function, system voltage, expected fault level, destination market and quantity. CHAC will review the request against the published model range.
