Calculadora de Dimensionamento de Cabos — Cobre/PVC
Dimensionar cabos de cobre/PVC em mm² utilizando a capacidade de corrente corrigida e a queda de tensão resistiva. Abrange três condutores carregados nos métodos ao ar A1, A2, B1, B2 e C.
Encontre o menor condutor de cobre/PVC listado que atenda aos critérios de classificação de corrente e de queda de tensão resistiva para um circuito trifásico equilibrado.
Resultado
Referência do condutor de cobre/PVC
6.00mm²Apenas verificações da tabela e da queda de resistência6 mm² é o menor condutor listado que atende aos limites de capacidade de corrente e queda de tensão resistiva inseridos.
Iz = Itabela × ktemperatura × koutro; Ib ≤ In ≤ Iz; ΔV% = 100 × √3 × I × ρ70 × L / (S × V)Figura selecionada G20 cobre/PVC, as fileiras abrangem três condutores carregados a 30°C de ar de referência, métodos A1/A2/B1/B2/C. A queda utiliza cobre resistivo a 70°C e exclui a reatância. Verifique separadamente a corrente operacional convencional do dispositivo de proteção, a suportabilidade a curto-circuito, os terminais e a carga do neutro/harmônicos.
Por que esse resultado?
Corrigido Iz ≥ 32.00 A; queda de tensão ≤ 3%. Método C, ambiente 30°C, correção total 1.000. Cobre/PVC, três condutores carregados; resistência a 70°C.
Referência selecionada e opções adjacentes listadas. Os valores são arredondados para exibição; as verificações utilizam valores não arredondados.
| Tamanho do cabo | Capacidade corrigida | Baixa de tensão | Razão |
|---|---|---|---|
| 4 mm² | 32.00 A · Atende ao requisito | 3.63% · Acima do limite | Queda de tensão acima do limite |
| 6 mm²Referência selecionada | 41.00 A · Atende ao requisito | 2.42% · Dentro do limite | Primeira partida registrada para esses controles |
| 10 mm² | 57.00 A · Atende ao requisito | 1.45% · Dentro do limite | Verificações atendidas; opção listada posteriormente |
Ver todas as opções marcadas de 16
| Tamanho do cabo | Capacidade corrigida | Baixa de tensão | Razão |
|---|---|---|---|
| 1.5 mm² | 17.50 A · Requisito abaixo | 9.67% · Acima do limite | Capacidade corrigida abaixo de In; Queda de tensão acima do limite |
| 2.5 mm² | 24.00 A · Requisito abaixo | 5.80% · Acima do limite | Capacidade corrigida abaixo de In; Queda de tensão acima do limite |
| 4 mm² | 32.00 A · Atende ao requisito | 3.63% · Acima do limite | Queda de tensão acima do limite |
| 6 mm²Referência selecionada | 41.00 A · Atende ao requisito | 2.42% · Dentro do limite | Primeira partida registrada para esses controles |
| 10 mm² | 57.00 A · Atende ao requisito | 1.45% · Dentro do limite | Verificações atendidas; opção listada posteriormente |
| 16 mm² | 76.00 A · Atende ao requisito | 0.91% · Dentro do limite | Verificações atendidas; opção listada posteriormente |
| 25 mm² | 96.00 A · Atende ao requisito | 0.58% · Dentro do limite | Verificações atendidas; opção listada posteriormente |
| 35 mm² | 119.00 A · Atende ao requisito | 0.41% · Dentro do limite | Verificações atendidas; opção listada posteriormente |
| 50 mm² | 144.00 A · Atende ao requisito | 0.29% · Dentro do limite | Verificações atendidas; opção listada posteriormente |
| 70 mm² | 184.00 A · Atende ao requisito | 0.21% · Dentro do limite | Verificações atendidas; opção listada posteriormente |
| 95 mm² | 223.00 A · Atende ao requisito | 0.15% · Dentro do limite | Verificações atendidas; opção listada posteriormente |
| 120 mm² | 259.00 A · Atende ao requisito | 0.12% · Dentro do limite | Verificações atendidas; opção listada posteriormente |
| 150 mm² | 299.00 A · Meets requirement | 0.10% · Within limit | Verificações atendidas; opção listada posteriormente |
| 185 mm² | 341.00 A · Meets requirement | 0.08% · Within limit | Verificações atendidas; opção listada posteriormente |
| 240 mm² | 403.00 A · Meets requirement | 0.06% · Within limit | Verificações atendidas; opção listada posteriormente |
| 300 mm² | 464.00 A · Meets requirement | 0.05% · Within limit | Verificações atendidas; opção listada posteriormente |
Still to confirm
- Verify short-circuit withstand, protective-device operating current, terminals and neutral/harmonic loading separately.
- This resistive estimate excludes cable reactance; the loaded table does not cover other conductor constructions or installation methods.
Data source: Electrical Installation Guide — Figure G20 copper/PVC reference (abre em nova aba)
Fórmula e método
Dimensionar cabos de cobre/PVC em mm² utilizando a capacidade de corrente corrigida e a queda de tensão resistiva. Abrange três condutores carregados nos métodos ao ar A1, A2, B1, B2 e C.
Como usar este calculador
- Confirm this table applies: copper, PVC, three loaded conductors and one of the listed air installation methods.
- Enter load current, protective-device current, route length, ambient temperature and a justified additional correction product.
- Review the smallest listed area meeting both current and resistive-drop checks, then verify fault withstand and all remaining installation conditions.
Limites de cálculo
Does not extrapolate to DC, two loaded conductors, aluminium, XLPE, buried cable or parallel circuits. The loaded 1.5–300 mm² table is a reference subset. AC reactance, harmonics, device I2 ≤ 1.45 Iz and full code compliance require separate checks.
Cable sizing calculation: ampacity and voltage drop
The loaded reference is Figure G20 of the Electrical Installation Guide: copper conductors, PVC insulation, three loaded conductors and a 70°C conductor limit. This version includes air-installation methods A1, A2, B1, B2 and C. It checks both corrected capacity and an entered resistive voltage-drop limit.
Introdução de notas
| Entrada | O que verificar |
|---|---|
| Current and protective-device rating | The input check requires Ib ≤ In. The search then requires the selected cable’s corrected Iz to be at least In. |
| Installation and correction | Choose the actual listed method. The air-temperature factor is applied internally; the additional correction product must exclude that same temperature factor. |
| Drop and conductor temperature | The voltage-drop estimate uses copper resistivity corrected from 20°C to 70°C. It excludes cable reactance and does not model harmonics or unequal phase loads. |
Exemplo prático · valores iniciais da forma
32 A circuit, copper/PVC clipped direct
Three loaded conductors · method C · 30°C air · other factor 1.00 · 400 V · one-way 50 m · drop limit 3%
4 mm² has 32 A base capacity but exceeds the entered 3% resistive-drop limit.
6 mm² has 41 A base/corrected capacity and approximately 2.42% resistive drop.
6.00 mm²
6 mm² is the first loaded row meeting both entered bounds. The cable still needs fault-withstand, terminal, neutral/harmonic and protective-device operating-current checks.
Cable sizing calculation: ampacity and voltage drop
Cable ampacity is the current a conductor can carry under stated installation and temperature conditions. Start with circuit design current Ib and protective-device rating In. Select a conductor whose corrected current capacity Iz is at least In, with Ib ≤ In.
Then check the route length against the chosen voltage-drop limit. The smallest cable that carries the current may still lose too much voltage on a long run. In the default example, 4 mm² meets 32 A base capacity in method C but fails the entered drop limit; 6 mm² is the first listed size meeting both checks.
A wire size calculator must use the right installation table
This version returns metric copper conductor areas for PVC insulation and three loaded conductors. It uses the stated air-installation methods A1, A2, B1, B2 and C, with a 70°C conductor limit. Select the actual installation method before comparing the table’s current values.
Corrected capacity equals the base table value multiplied by the air-temperature factor and your additional correction product. Grouping or other applicable factors can reduce capacity further. Do not include the air-temperature factor again in the extra field; it is already applied by the calculator.
Cable size and circuit breaker rating must be checked together
Increasing a breaker rating without checking the cable can remove the intended overload protection. Recheck corrected ampacity whenever device rating, route conditions or grouping changes. Also verify protective-device operating-current requirements and cable short-circuit withstand.
The voltage-drop result here is a resistive estimate using copper resistance at 70°C. Cable reactance, harmonic currents and neutral loading require additional assessment. The table does not cover AWG, aluminium, XLPE, buried cables, DC circuits or parallel conductors; those need their own verified sizing data.
Keep the table conditions attached to the result
- Do not apply these three-loaded-conductor PVC rows to DC, two-loaded-conductor circuits, XLPE, aluminium, buried cable or parallel conductors. Those require the appropriate separate tables and corrections.
- Ib ≤ In ≤ Iz is one part of conductor protection. Verify the applicable conventional operating-current condition, short-circuit withstand, disconnection conditions and voltage drop using the complete installation data.
Perguntas frequentes
Why does this version only support copper/PVC and three loaded conductors?
Those are the verified table conditions loaded into the calculator. Other constructions require different source data and must not be inferred from these values.
Why can a cable pass ampacity but fail the tool?
A long route can exceed the chosen voltage-drop limit even when corrected current capacity is sufficient. Both checks must be met.
Should I include ambient temperature in the extra correction product?
No. The selected temperature factor is already applied. Use the extra field for justified additional factors such as grouping, without counting the same effect twice.
Does this verify the neutral conductor and short-circuit withstand?
No. These require separate checks, particularly where harmonics load the neutral or the protective device limits fault energy.
Does this wire size calculator return AWG sizes?
No. It selects from the loaded metric copper/PVC table in mm². Converting area to an approximate AWG designation does not transfer the table’s ampacity to a different cable construction or installation standard.
Can I increase the circuit breaker size when voltage drop is too high?
A larger breaker does not reduce cable resistance or voltage drop. Review conductor area, length and installation conditions, then check the protective device against the selected cable’s corrected current capacity.
Precisa de ajuda para escolher um produto da CHAC?
Envie a tensão do sistema, a corrente de carga e as condições de instalação junto com sua solicitação.
Copper/PVC cable current-carrying capacity
Base ampacity values from Electrical Installation Guide, Figure G20. This is an external installation reference, not a CHAC cable product rating.
Reference data. Calculate to highlight the matching row.
Scroll horizontally on small screens to read all columns.
| Conductor area (mm²) | A1 (A) | A2 (A) | B1 (A) | B2 (A) | C (A) |
|---|---|---|---|---|---|
| 1.5Current reference | 13.5 | 13 | 15.5 | 15 | 17.5 |
| 2.5Current reference | 18 | 17.5 | 21 | 20 | 24 |
| 4Current reference | 24 | 23 | 28 | 27 | 32 |
| 6Current reference | 31 | 29 | 36 | 34 | 41 |
| 10Current reference | 42 | 39 | 50 | 46 | 57 |
| 16Current reference | 56 | 52 | 68 | 62 | 76 |
| 25Current reference | 73 | 68 | 89 | 80 | 96 |
| 35Current reference | 89 | 83 | 110 | 99 | 119 |
| 50Current reference | 108 | 99 | 134 | 118 | 144 |
| 70Current reference | 136 | 125 | 171 | 149 | 184 |
| 95Current reference | 164 | 150 | 207 | 179 | 223 |
| 120Current reference | 188 | 172 | 239 | 206 | 259 |
| 150Current reference | 216 | 196 | 262 | 225 | 299 |
| 185Current reference | 245 | 223 | 296 | 255 | 341 |
| 240Current reference | 286 | 261 | 346 | 297 | 403 |
| 300Current reference | 328 | 298 | 394 | 339 | 464 |
- A1
- Insulated conductors in conduit in a thermally insulated wall.
- A2
- Multicore cable in conduit in a thermally insulated wall.
- B1
- Insulated conductors in conduit on a wall.
- B2
- Multicore cable in conduit on a wall.
- C
- Cable clipped direct or on an unperforated tray, within the source method conditions.
Reading this reference
- Copper conductors, PVC insulation, three loaded conductors, 70°C conductor limit and 30°C ambient air. Only methods A1, A2, B1, B2 and C are reproduced.
- The numbers in this reference table remain the base values. The calculator applies temperature and other entered correction factors separately.
- Do not apply these values to aluminium, XLPE, DC circuits, two loaded conductors, buried cables or parallel conductors. Verify the complete installation conditions in the source.
Source: Electrical Installation Guide — Figure G20 and installation methods (abre em nova aba)
Source checked: . This is the retrieval date, not a standard edition or product revision date.
Exemplo de aplicação · Informações ilustrativas
Checking a warm equipment feeder for ampacity and drop
For a 40 A load and 40 A protective-device reference, consider an 80 m, 400 V three-phase copper/PVC route using method B2, 40°C ambient and an entered grouping factor of 0.80. The calculator returns 16 mm²: its 62 A base capacity becomes 43.15 A after correction, and the resistive voltage drop is 1.81%, below the example’s 3% target. The cable values are installation-reference data, not CHAC cable ratings. When reviewing PXB6-63 or CQM6 protection, also check the actual route, fault withstand and trip behavior; passing voltage drop alone does not establish cable suitability.
Dados do produto: Disjuntor Miniatura PXB6-63 · Fabricante OEM de Disjuntor de Caixa Moldada (MCCB) Padrão CQM6



