PXL6-100B Disjoncteur à courant résiduel électromagnétique
The CHAC PXL6-100B electromagnetic RCCB provides Type B residual-current protection for AC circuits, with rated currents from 10A to 100A. Select the sensitivity and pole arrangement for the circuit, and coordinate separate overcurrent protection with the published conditional short-circuit rating.
Vue d'ensemble du produit
Le CHAC PXL6-100B Type B electromagnetic RCCB provides residual-current protection for AC circuits requiring Type B detection. Rated currents extend from 10A to 100A, while overload and short-circuit protection must be supplied by a coordinated protective device.
Pour les importateurs, les distributeurs et les fabricants d’équipements, CHAC peut vérifier la configuration demandée au regard des exigences du circuit électrique et des documents propres au marché de destination. Convenez du modèle exact, des schémas et des exigences de marquage avant l’approbation des échantillons ou la passation d’une commande répétée.
Points clés de sélection
Applications typiques
Evaluate PXL6-100B for circuits whose equipment instructions call for Type B residual-current detection. Confirm waveform coverage, sensitivity, poles and the complete protective arrangement before specifying it for an inverter, drive or charging installation.
Demandes d’admission et guide de sélection
| Article sélectionné | PXL6-100B configuration | Qu'est-ce que l'on doit vérifier ? |
|---|---|---|
| Residual-current type | Type B | Select for the equipment waveform requirements; this is not an overcurrent trip curve. |
| Current range | 10–100A | Match the carrying current and assembly design; provide separate overcurrent protection. |
| Arrangement d'approvisionnement | 230V AC: 1P+N; 400V AC: 3P / 3P+N | Confirm the exact terminal and neutral arrangement. |
| Short-circuit coordination | 6000A conditional rating | Check the backup protective device and applicable test conditions. |
Use these checks to compare the protection function, configuration and related CHAC products before specifying PXL6-100B. Related products are selection alternatives or system components, not automatic replacements.
Use Type B only where the protection design calls for it
Type B selection depends on the residual-current waveforms that equipment can produce and the installation requirements.
Check coordination before replacing a Type AC or A device
Review the sensitivity, time behavior, pole arrangement, supply rating and backup protection together.
Compare PXL6-100 for the required function
Le disjoncteur différentiel électromagnétique CHAC PXL6-100 offre une protection contre les courants résiduels avec des options de type AC ou type A et des courants nominaux allant de 10A à 100A. Adaptez la sensibilité et la disposition des pôles au circuit, et assurez une protection coordonnée contre les surintensités pour l’installation.
Compare PXB6L-63B for the required function
Le disjoncteur différentiel électromagnétique CHAC PXB6L-63B combine la protection contre les surcharges et les courts-circuits avec la protection différentielle de type B. Sa gamme 6–63A comprend quatre configurations polaires et des courbes de déclenchement B/C/D, permettant d’obtenir une configuration adaptée aux exigences du circuit et de la protection différentielle.
Need Help Specifying PXL6-100B?
Veuillez transmettre les spécifications du circuit, la configuration sélectionnée, le marché cible et la quantité souhaitée afin d’effectuer une analyse spécifique au modèle.
Use Type B only where the protection design calls for it
Type B selection depends on the residual-current waveforms that equipment can produce and the installation requirements. It does not mean that the RCCB is suitable as a DC circuit breaker, or that it replaces equipment-specific protection instructions.
Check coordination before replacing a Type AC or A device
Review the sensitivity, time behavior, pole arrangement, supply rating and backup protection together. For the PXL6-100B, confirm the exact sensitivity and operating-time documentation before approving a replacement or repeat order.
How to Specify a PXL6-100B Order
Utilisez les détails de configuration ci-dessous dans la spécification d’achat. Conservez la révision approuvée du dessin et l’identification du produit avec la commande afin que les livraisons ultérieures puissent être contrôlées de manière cohérente.
| Détail de la commande | Informations à inclure |
|---|---|
| Residual-current type | Type B — Select for the equipment waveform requirements; this is not an overcurrent trip curve. |
| Current range | 10–100A — Match the carrying current and assembly design; provide separate overcurrent protection. |
| Arrangement d'approvisionnement | 230V AC: 1P+N; 400V AC: 3P / 3P+N — Confirm the exact terminal and neutral arrangement. |
| Short-circuit coordination | 6000A conditional rating — Check the backup protective device and applicable test conditions. |
| Projet et documents | Fournissez les exigences documentaires relatives à l’application, aux conditions d’installation et au marché de destination. |
| Quantité et identification | Précisez la quantité, les exigences relatives aux échantillons, la langue d’emballage et toute proposition de marque ; confirmez la faisabilité avant approbation. |
Vérifiez l’ajustement de l’installation avant approbation
Caractéristiques techniques
| Paramètre | |
| Tension nominale | 230V AC(1P+N); 400V AC(3P、3P+N) |
| Courant nominal (A) | 10A、16A、20A、25A、32A、40A、50A、63A、80A、100A |
| Courant résiduel opérationnel assigné | 10mA(10A~40A), 30mA, 100mA, 400mA |
| Courant résiduel assigné de non-fonctionnement | 0.5IΔn |
| Type of Residual Current(with DC component) | B type |
| Nombre de Polonais | 1P+N、3P、3P+N |
| Courant de court-circuit assigné conditionnel | 6000A |
| Courant de court-circuit résiduel conditionnel assigné | 6000A |
| Capacité nominale de fermeture et de coupure | 630A(In≤63A); 10In(In>63A) |
| Capacité nominale de fermeture et de coupure en charge résiduelle | 630A(In≤63A); 10In(In>63A) |
| Couple de serrage | (2.5～3.0)N.m |
| Classe de protection | IP20 |
| Degré de pollution | 2 |
| Catégorie d'installation | Ⅱ |
| Normes | GB 16916.1, IEC61008-1 |
| Certification | CE CB CCC |DEKRA Certified |
Temps de fonctionnement (pour les dispositifs à courant résiduel)
| Dans (A) | IΔn (A) | Découpage lorsque le courant résiduel atteint les valeurs suivantes | ||||
| Je ne sais pas | 2IΔn | 5IΔn | 5A, 10A, 20A, 50A, 100A, 200A | IΔt | ||
| 10～100A | 0.03、0.01、0.1、0.3 | 0.3 | 0.15 | 0.04 | 0.04 | 0.04 |
Endurance mécanique et endurance électrique
| Dans (A) | Nombre de cycles de fonctionnement | Operating frequency (cycles per hour) | |
| Number of on-load operating cycles | Number of no-load operating cycles | ||
| 10～25A | 2000 | 2000 | 240 |
| 32A～100A | 2000 | 1000 | 120 |
Designation de type
Dimensions (mm)
Pourquoi choisir CHAC
CHAC Electric supplies electrical protection and control products for importers, distributors and equipment brands. For PXL6-100B, agree the configuration, technical documents, approved sample and identification requirements before production. The company facilities shown below provide company context, not a claim that every model uses the same production or test process.
01
CONFIRM THE SPECIFICATION
Agree the PXL6-100B configuration, circuit duty and installation requirements.
02
REVIEW THE DOCUMENTS
Confirm model-specific drawings and destination-market requirements.
03
APPROVE THE SAMPLE
Record the accepted configuration and marking requirements.
04
DEFINE ORDER CHECKS
Agree packaging, identification and delivery requirements in the quotation.
Ligne de montage automatisée
Laboratoire d'essai
Injection et estampage
Inspection de qualité
Qu'est-ce que nous pouvons personnaliser ?
Discuss PXL6-100B product identification, packaging and documentation with CHAC. Each proposed change is subject to technical feasibility, marking rules and approval of the exact order; no altered rating or certification is implied.
Logo et identité visuelle
Submit logo artwork and marking requirements for review against the available print area and mandatory product markings.
Packaging & Manuals
Define carton labels, packaging language, product identification and instruction requirements for the destination market.
Configuration Selection
Specify PXL6-100B with the required residual-current type, operating conditions and protection duty. Confirm the complete order combination.
Assembly Requirements
Provide the mounting and connection requirements for review. Changes to the housing, terminals or operating arrangement require engineering approval.
Market Documentation
Request documents covering the exact PXL6-100B model and destination market. A standard reference alone is not evidence of certification.
Sample Approval
Agree the sample specification, drawing revision and acceptance criteria before confirming a production order.
Technical Documents and Support
PXL6-100B Technical Documents
Request the PXL6-100B datasheet, configuration drawing, installation instructions and available model-specific market documents.Request Datasheet
Dois-je avoir des documents techniques ?
Send the application, electrical requirements, assembly layout and destination market for configuration and document review.Contactez-nous
PXL6-100B Product FAQ
What is the difference between Type A and Type B RCCBs?
Type B provides broader specified residual-current waveform coverage, including smooth DC detection under its applicable conditions. Select according to the equipment and installation requirements. PXL6-100B is the Type B model; confirm the exact device documentation.
Can PXL6-100B replace an MCB?
No. It is an RCCB and does not provide integral overload and short-circuit protection. Use a coordinated overcurrent device, or evaluate an appropriate Type B RCBO if integrated protection is required.
Is a Type B RCCB the same as a B-curve circuit breaker?
No. Type B describes residual-current detection, while a B curve describes an overcurrent trip characteristic. PXL6-100B is not specified by an MCB B/C/D curve.
How should I choose the PXL6-100B residual-current sensitivity?
Select the mA rating from the circuit purpose, equipment instructions and local requirements. Rated current in amperes is a separate specification. Confirm the exact PXL6-100B sensitivity variant and its operating-time data rather than using a larger threshold to mask recurring trips.
Why can a PXL6-100B installation trip repeatedly?
Possible causes include insulation faults, accumulated equipment leakage, incorrect neutral connections or an unsuitable protection type. Have a qualified person investigate the circuit and follow the device test instructions before changing the rating or replacing protection.
What should an importer include in a PXL6-100B inquiry?
Specify poles, AC supply, rated current, residual-current type and sensitivity, plus the overcurrent curve if ordering an RCBO. Add the destination market, required documents, quantity and marking requirements so the quotation identifies the exact configuration.
Specify the Right PXL6-100B Configuration
Send CHAC your required configuration, application, destination market and estimated quantity. We will review the requested specification and provide the relevant technical documents and commercial proposal.
Produits similaires
-
PXL6a-100 Disjoncteur à courant résiduel électromagnétique
-
Disjoncteurs miniatures de la série PXB9N-32 avec fonction d'isolation
-
Disjoncteur miniature à fuite électromagnétique de la série PXB9L-40
-
FB2L-63 Disjoncteur de courant résiduel avec protection contre les surintensités – Type électromagnétique