Kalkulator Ukuran Kabel — Tembaga/PVC
Ukuran kabel tembaga/PVC dalam mm² menggunakan daya hantar arus yang telah dikoreksi dan penurunan tegangan resistif. Mencakup tiga konduktor beraliran pada metode udara A1, A2, B1, B2, dan C.
Temukan konduktor tembaga/PVC terkecil yang terdaftar yang memenuhi persyaratan daya hantar arus dan penurunan tegangan resistif yang dimasukkan untuk rangkaian tiga fase seimbang.
Hasilnya
Referensi konduktor tembaga/PVC
6.00mm²Hanya pemeriksaan tabel dan penurunan resistansi6 mm² adalah konduktor terkecil yang terdaftar yang memenuhi batas kapasitas arus dan penurunan tegangan resistif yang dimasukkan.
Iz = Itable × ktemperature × kother; Ib ≤ In ≤ Iz; ΔV% = 100 × √3 × I × ρ70 × L / (S × V)Gambar yang dipilih G20 menunjukkan baris tembaga/PVC yang meliputi tiga konduktor berbeban pada suhu udara referensi 30°C, metode A1/A2/B1/B2/C. Penurunan menggunakan resistansi tembaga pada 70°C dan tidak memperhitungkan reaktansi. Periksa arus operasi konvensional perangkat proteksi, ketahanan terhadap arus pendek, terminal, serta beban netral/harmonik secara terpisah.
Mengapa hasil ini?
Koreksi Iz ≥ 32.00 A; penurunan tegangan ≤ 3%. Metode C, suhu sekitar 30°C, koreksi total 1.000. Tembaga/PVC, tiga konduktor yang terbeban; resistansi pada 70°C.
Referensi yang dipilih dan opsi terdaftar yang berdekatan. Nilai-nilai dibulatkan untuk ditampilkan; pengecekan menggunakan nilai yang tidak dibulatkan.
| Ukuran kabel | Kapasitas yang telah dikoreksi | Penurunan tegangan | Alasan |
|---|---|---|---|
| 4 mm² | 32.00 A · Memenuhi persyaratan | 3.63% · Di atas batas | Penurunan tegangan di atas batas |
| 6 mm²Referensi yang dipilih | 41.00 A · Memenuhi persyaratan | 2.42% · Dalam batas | Pertandingan pertama yang terdaftar untuk pemeriksaan ini |
| 10 mm² | 57.00 A · Memenuhi persyaratan | 1.45% · Dalam batas | Cek telah dipenuhi; opsi yang terdaftar kemudian |
Lihat semua opsi yang telah diperiksa 16
| Ukuran kabel | Kapasitas yang telah dikoreksi | Penurunan tegangan | Alasan |
|---|---|---|---|
| 1.5 mm² | 17.50 A · Persyaratan di bawah | 9.67% · Di atas batas | Kapasitas yang dikoreksi di bawah In; Tegangan turun melebihi batas |
| 2.5 mm² | 24.00 A · Persyaratan di bawah | 5.80% · Di atas batas | Kapasitas yang dikoreksi di bawah In; Tegangan turun melebihi batas |
| 4 mm² | 32.00 A · Memenuhi persyaratan | 3.63% · Di atas batas | Penurunan tegangan di atas batas |
| 6 mm²Referensi yang dipilih | 41.00 A · Memenuhi persyaratan | 2.42% · Dalam batas | Pertandingan pertama yang terdaftar untuk pemeriksaan ini |
| 10 mm² | 57.00 A · Memenuhi persyaratan | 1.45% · Dalam batas | Cek telah dipenuhi; opsi yang terdaftar kemudian |
| 16 mm² | 76.00 A · Memenuhi persyaratan | 0.91% · Dalam batas | Cek telah dipenuhi; opsi yang terdaftar kemudian |
| 25 mm² | 96.00 A · Memenuhi persyaratan | 0.58% · Dalam batas | Cek telah dipenuhi; opsi yang terdaftar kemudian |
| 35 mm² | 119.00 A · Memenuhi persyaratan | 0.41% · Dalam batas | Cek telah dipenuhi; opsi yang terdaftar kemudian |
| 50 mm² | 144.00 A · Memenuhi persyaratan | 0.29% · Dalam batas | Cek telah dipenuhi; opsi yang terdaftar kemudian |
| 70 mm² | 184.00 A · Memenuhi persyaratan | 0.21% · Dalam batas | Cek telah dipenuhi; opsi yang terdaftar kemudian |
| 95 mm² | 223.00 A · Memenuhi persyaratan | 0.15% · Dalam batas | Cek telah dipenuhi; opsi yang terdaftar kemudian |
| 120 mm² | 259.00 A · Memenuhi persyaratan | 0.12% · Dalam batas | Cek telah dipenuhi; opsi yang terdaftar kemudian |
| 150 mm² | 299.00 A · Memenuhi persyaratan | 0.10% · Dalam batas | Cek telah dipenuhi; opsi yang terdaftar kemudian |
| 185 mm² | 341.00 A · Memenuhi persyaratan | 0.08% · Dalam batas | Cek telah dipenuhi; opsi yang terdaftar kemudian |
| 240 mm² | 403.00 A · Memenuhi persyaratan | 0.06% · Dalam batas | Cek telah dipenuhi; opsi yang terdaftar kemudian |
| 300 mm² | 464.00 A · Memenuhi persyaratan | 0.05% · Dalam batas | Cek telah dipenuhi; opsi yang terdaftar kemudian |
Masih akan dikonfirmasi
- Verifikasi ketahanan terhadap arus pendek, arus operasi perangkat proteksi, terminal, serta beban netral/harmonik secara terpisah.
- Estimasi resistansi ini tidak memperhitungkan reaktansi kabel; tabel beban tidak mencakup konstruksi konduktor atau metode pemasangan lainnya.
Sumber data: Panduan Instalasi Listrik — Gambar G20 referensi tembaga/PVC (buka di tab baru)
Formula dan metode
Ukuran kabel tembaga/PVC dalam mm² menggunakan daya hantar arus yang telah dikoreksi dan penurunan tegangan resistif. Mencakup tiga konduktor beraliran pada metode udara A1, A2, B1, B2, dan C.
Cara menggunakan kalkulator ini
- Konfirmasikan bahwa tabel ini berlaku untuk: tembaga, PVC, tiga konduktor yang dibebani, dan salah satu metode pemasangan di udara yang tercantum.
- Masukkan arus beban, arus perangkat proteksi, panjang jalur, suhu sekitar, serta faktor koreksi tambahan yang dibenarkan.
- Tinjau area terkecil yang terdaftar yang memenuhi baik persyaratan saat ini maupun persyaratan penurunan tegangan, kemudian verifikasi ketahanan terhadap gangguan dan semua kondisi instalasi yang tersisa.
Batas perhitungan
Tidak dapat diterapkan pada DC, dua konduktor yang terbebani, aluminium, kabel XLPE, kabel yang tertanam, atau rangkaian paralel. Tabel 1.5–300 mm² untuk konduktor yang terbebani merupakan subset referensi. Reaktansi AC, harmonisa, perangkat I2 ≤ 1.45 Iz, serta kepatuhan penuh terhadap kode memerlukan pemeriksaan terpisah.
Cable sizing calculation: ampacity and voltage drop
The loaded reference is Figure G20 of the Electrical Installation Guide: copper conductors, PVC insulation, three loaded conductors and a 70°C conductor limit. This version includes air-installation methods A1, A2, B1, B2 and C. It checks both corrected capacity and an entered resistive voltage-drop limit.
Catatan masukan
| Masukan | Apa yang harus diperiksa |
|---|---|
| Current and protective-device rating | The input check requires Ib ≤ In. The search then requires the selected cable’s corrected Iz to be at least In. |
| Installation and correction | Choose the actual listed method. The air-temperature factor is applied internally; the additional correction product must exclude that same temperature factor. |
| Drop and conductor temperature | The voltage-drop estimate uses copper resistivity corrected from 20°C to 70°C. It excludes cable reactance and does not model harmonics or unequal phase loads. |
Contoh kerja · nilai awal formulir
32 A circuit, copper/PVC clipped direct
Three loaded conductors · method C · 30°C air · other factor 1.00 · 400 V · one-way 50 m · drop limit 3%
4 mm² has 32 A base capacity but exceeds the entered 3% resistive-drop limit.
6 mm² has 41 A base/corrected capacity and approximately 2.42% resistive drop.
6.00 mm²
6 mm² is the first loaded row meeting both entered bounds. The cable still needs fault-withstand, terminal, neutral/harmonic and protective-device operating-current checks.
Cable sizing calculation: ampacity and voltage drop
Cable ampacity is the current a conductor can carry under stated installation and temperature conditions. Start with circuit design current Ib and protective-device rating In. Select a conductor whose corrected current capacity Iz is at least In, with Ib ≤ In.
Then check the route length against the chosen voltage-drop limit. The smallest cable that carries the current may still lose too much voltage on a long run. In the default example, 4 mm² meets 32 A base capacity in method C but fails the entered drop limit; 6 mm² is the first listed size meeting both checks.
A wire size calculator must use the right installation table
This version returns metric copper conductor areas for PVC insulation and three loaded conductors. It uses the stated air-installation methods A1, A2, B1, B2 and C, with a 70°C conductor limit. Select the actual installation method before comparing the table’s current values.
Corrected capacity equals the base table value multiplied by the air-temperature factor and your additional correction product. Grouping or other applicable factors can reduce capacity further. Do not include the air-temperature factor again in the extra field; it is already applied by the calculator.
Cable size and circuit breaker rating must be checked together
Increasing a breaker rating without checking the cable can remove the intended overload protection. Recheck corrected ampacity whenever device rating, route conditions or grouping changes. Also verify protective-device operating-current requirements and cable short-circuit withstand.
The voltage-drop result here is a resistive estimate using copper resistance at 70°C. Cable reactance, harmonic currents and neutral loading require additional assessment. The table does not cover AWG, aluminium, XLPE, buried cables, DC circuits or parallel conductors; those need their own verified sizing data.
Keep the table conditions attached to the result
- Do not apply these three-loaded-conductor PVC rows to DC, two-loaded-conductor circuits, XLPE, aluminium, buried cable or parallel conductors. Those require the appropriate separate tables and corrections.
- Ib ≤ In ≤ Iz is one part of conductor protection. Verify the applicable conventional operating-current condition, short-circuit withstand, disconnection conditions and voltage drop using the complete installation data.
Pertanyaan yang sering diajukan
Why does this version only support copper/PVC and three loaded conductors?
Those are the verified table conditions loaded into the calculator. Other constructions require different source data and must not be inferred from these values.
Why can a cable pass ampacity but fail the tool?
A long route can exceed the chosen voltage-drop limit even when corrected current capacity is sufficient. Both checks must be met.
Should I include ambient temperature in the extra correction product?
No. The selected temperature factor is already applied. Use the extra field for justified additional factors such as grouping, without counting the same effect twice.
Does this verify the neutral conductor and short-circuit withstand?
No. These require separate checks, particularly where harmonics load the neutral or the protective device limits fault energy.
Does this wire size calculator return AWG sizes?
No. It selects from the loaded metric copper/PVC table in mm². Converting area to an approximate AWG designation does not transfer the table’s ampacity to a different cable construction or installation standard.
Can I increase the circuit breaker size when voltage drop is too high?
A larger breaker does not reduce cable resistance or voltage drop. Review conductor area, length and installation conditions, then check the protective device against the selected cable’s corrected current capacity.
Perlu bantuan memilih produk CHAC?
Sertakan tegangan sistem, arus beban, dan kondisi pemasangan dalam pertanyaan Anda.
Copper/PVC cable current-carrying capacity
Base ampacity values from Electrical Installation Guide, Figure G20. This is an external installation reference, not a CHAC cable product rating.
Reference data. Calculate to highlight the matching row.
Scroll horizontally on small screens to read all columns.
| Conductor area (mm²) | A1 (A) | A2 (A) | B1 (A) | B2 (A) | C (A) |
|---|---|---|---|---|---|
| 1.5Current reference | 13.5 | 13 | 15.5 | 15 | 17.5 |
| 2.5Current reference | 18 | 17.5 | 21 | 20 | 24 |
| 4Current reference | 24 | 23 | 28 | 27 | 32 |
| 6Current reference | 31 | 29 | 36 | 34 | 41 |
| 10Current reference | 42 | 39 | 50 | 46 | 57 |
| 16Current reference | 56 | 52 | 68 | 62 | 76 |
| 25Current reference | 73 | 68 | 89 | 80 | 96 |
| 35Current reference | 89 | 83 | 110 | 99 | 119 |
| 50Current reference | 108 | 99 | 134 | 118 | 144 |
| 70Current reference | 136 | 125 | 171 | 149 | 184 |
| 95Current reference | 164 | 150 | 207 | 179 | 223 |
| 120Current reference | 188 | 172 | 239 | 206 | 259 |
| 150Current reference | 216 | 196 | 262 | 225 | 299 |
| 185Current reference | 245 | 223 | 296 | 255 | 341 |
| 240Current reference | 286 | 261 | 346 | 297 | 403 |
| 300Current reference | 328 | 298 | 394 | 339 | 464 |
- A1
- Insulated conductors in conduit in a thermally insulated wall.
- A2
- Multicore cable in conduit in a thermally insulated wall.
- B1
- Insulated conductors in conduit on a wall.
- B2
- Multicore cable in conduit on a wall.
- C
- Cable clipped direct or on an unperforated tray, within the source method conditions.
Reading this reference
- Copper conductors, PVC insulation, three loaded conductors, 70°C conductor limit and 30°C ambient air. Only methods A1, A2, B1, B2 and C are reproduced.
- The numbers in this reference table remain the base values. The calculator applies temperature and other entered correction factors separately.
- Do not apply these values to aluminium, XLPE, DC circuits, two loaded conductors, buried cables or parallel conductors. Verify the complete installation conditions in the source.
Source: Electrical Installation Guide — Figure G20 and installation methods (buka di tab baru)
Source checked: . This is the retrieval date, not a standard edition or product revision date.
Contoh aplikasi · Masukan ilustratif
Checking a warm equipment feeder for ampacity and drop
For a 40 A load and 40 A protective-device reference, consider an 80 m, 400 V three-phase copper/PVC route using method B2, 40°C ambient and an entered grouping factor of 0.80. The calculator returns 16 mm²: its 62 A base capacity becomes 43.15 A after correction, and the resistive voltage drop is 1.81%, below the example’s 3% target. The cable values are installation-reference data, not CHAC cable ratings. When reviewing PXB6-63 or CQM6 protection, also check the actual route, fault withstand and trip behavior; passing voltage drop alone does not establish cable suitability.
Data produk: PXB6-63 Pemutus Sirkuit Miniatur · CQM6 Standard Molded Case Circuit Breaker (MCCB) Produsen OEM



