Calculador de corrente de motor
Estime a corrente de plena carga do motor com base na potência no eixo em kW, na tensão, na eficiência e no fator de potência. Compare a estimativa com os dados da placa de identificação do motor antes de selecionar o equipamento de comando.
Estime a corrente de plena carga antes de verificar as classificações do contator, do relé de sobrecarga ou do dispositivo de proteção do motor.
Resultado
Corrente estimada do motor
20.75ACálculo preliminarI = P × 1,000 / (√3 × V × PF × η)Estimate only. Use motor nameplate current for final protection and control-device selection. Starting current, duty and overload settings are not calculated.
Por que esse resultado?
Fórmula e método
Estime a corrente de plena carga do motor com base na potência no eixo em kW, na tensão, na eficiência e no fator de potência. Compare a estimativa com os dados da placa de identificação do motor antes de selecionar o equipamento de comando.
Como usar este calculador
- Enter the mechanical shaft output stated on the motor nameplate.
- Select supply type, voltage and the known AC power factor.
- Enter efficiency as a percentage.
Limites de cálculo
K is √3 for balanced three-phase and 1 otherwise. PF is omitted for DC. Efficiency η is used as a decimal. Starting duty and manufacturer ratings require separate verification.
Motor FLA: estimating full-load amps from shaft power
A motor must draw more electrical power than it delivers at the shaft because some energy is lost as heat and other losses. Efficiency accounts for this difference. AC power factor is a separate relationship between real and apparent power; both affect a current estimate.
Introdução de notas
| Entrada | O que verificar |
|---|---|
| Shaft power | Use the mechanical output rating in kW at the operating point being assessed. Do not enter electrical input power as shaft output. |
| Efficiency | Enter a percentage, such as 90 for 90%. The equation uses the decimal 0.90. |
| Voltage and PF | Use line-to-line voltage for a balanced three-phase motor and the corresponding operating power factor. Both PF and efficiency can vary with load. |
Exemplo prático · valores iniciais da forma
11 kW motor at 90% efficiency
Three-phase · 400 V · PF 0.85 · shaft output 11 kW · efficiency 90%
Electrical input = 11 / 0.90 = 12.22 kW
I = 11,000 / (√3 × 400 × 0.85 × 0.90)
Estimated running current = 20.75 A
20.75 A
This estimates running current at the stated output, efficiency and power factor. It does not predict locked-rotor current or the supply current of a variable-speed drive.
Using the result for motor control
- Use nameplate current and the manufacturer’s instructions for the actual voltage and winding connection when setting overload protection.
- Check contactor utilization category, starts per hour, starting method and protective-device coordination. Running amperes alone do not define the required motor starter.
Perguntas frequentes
Should I use this estimate or the motor nameplate?
Use the manufacturer’s nameplate current for final control and protection selection. This estimate helps when only shaft power, efficiency and power factor are available.
Are efficiency and power factor the same thing?
No. Efficiency compares shaft output with real electrical input. Power factor compares real with apparent AC power. A motor can have high efficiency and still draw reactive current.
Can I calculate starting current with this tool?
No. Starting current depends on motor design, starting method and supply conditions. Use manufacturer data for direct-on-line, star-delta, soft-starter or drive applications.
Is the estimate valid on the input side of a VFD?
Not as a drive-input calculation. Drive losses, harmonics and input power factor differ from the motor-terminal conditions used here. Check the drive manufacturer’s input-current data.
Precisa de ajuda para escolher um produto da CHAC?
Envie a tensão do sistema, a corrente de carga e as condições de instalação junto com sua solicitação.
Exemplo de aplicação · Informações ilustrativas
Estimating current for a 15 kW pump control panel
When preparing a pump control panel before the final motor nameplate is available, shaft power alone is not enough to estimate current. A 15 kW motor at 400 V three-phase, power factor 0.85 and 90% efficiency gives 28.30 A in this calculator. That estimate helps narrow the CHAC CQC6 contactor and CQR2 overload-relay data to review. It does not establish a complete starter combination. Once the motor is confirmed, use its actual nameplate current and starting duty to check the contactor ratings, overload range and short-circuit protection.
Dados do produto: Fabricante OEM de Contactores AC Industriais Série CQC6 · Relé de sobrecarga térmico da série CQR2



