Kalkulator Arus Motor
Perkirakan arus beban penuh motor berdasarkan daya poros dalam kW, tegangan, efisiensi, dan faktor daya. Periksa perkiraan tersebut dengan data pada pelat nama motor sebelum memilih peralatan kontrol.
Perkirakan arus beban penuh sebelum memeriksa rating kontaktor, relay beban lebih, atau perlindungan motor.
Hasilnya
Arus motor perkiraan
20.75APerhitungan awalI = P × 1,000 / (√3 × V × PF × η)Hanya perkiraan. Gunakan arus pada papan nama motor untuk pemilihan perangkat proteksi dan kontrol yang final. Pengaturan arus mulai, derajat operasi, dan beban lebih tidak dihitung.
Mengapa hasil ini?
Formula dan metode
Perkirakan arus beban penuh motor berdasarkan daya poros dalam kW, tegangan, efisiensi, dan faktor daya. Periksa perkiraan tersebut dengan data pada pelat nama motor sebelum memilih peralatan kontrol.
Cara menggunakan kalkulator ini
- Masukkan nilai keluaran poros mekanis yang tertera pada papan nama motor.
- Pilih jenis suplai, tegangan, dan faktor daya AC yang diketahui.
- Masukkan efisiensi dalam bentuk persentase.
Batas perhitungan
K adalah √3 untuk tiga fase seimbang dan 1 jika tidak. PF dihilangkan untuk DC. Efisiensi η digunakan sebagai angka desimal. Beban mulai dan peringkat pabrikan memerlukan verifikasi terpisah.
Motor FLA: memperkirakan arus beban penuh dari daya poros
Sebuah motor harus menyerap daya listrik yang lebih besar daripada daya yang dihasilkannya pada porosnya, karena sebagian energi hilang dalam bentuk panas dan kerugian lainnya. Efisiensi menggambarkan perbedaan ini. Faktor daya AC merupakan hubungan terpisah antara daya aktif dan daya semu; keduanya memengaruhi estimasi arus.
Catatan masukan
| Masukan | Apa yang harus diperiksa |
|---|---|
| Daya poros | Use the mechanical output rating in kW at the operating point being assessed. Do not enter electrical input power as shaft output. |
| Efisiensi | Enter a percentage, such as 90 for 90%. The equation uses the decimal 0.90. |
| Voltage and PF | Use line-to-line voltage for a balanced three-phase motor and the corresponding operating power factor. Both PF and efficiency can vary with load. |
Contoh kerja · nilai awal formulir
11 kW motor at 90% efficiency
Three-phase · 400 V · PF 0.85 · shaft output 11 kW · efficiency 90%
Electrical input = 11 / 0.90 = 12.22 kW
I = 11,000 / (√3 × 400 × 0.85 × 0.90)
Estimated running current = 20.75 A
20.75 A
This estimates running current at the stated output, efficiency and power factor. It does not predict locked-rotor current or the supply current of a variable-speed drive.
Using the result for motor control
- Use nameplate current and the manufacturer’s instructions for the actual voltage and winding connection when setting overload protection.
- Check contactor utilization category, starts per hour, starting method and protective-device coordination. Running amperes alone do not define the required motor starter.
Pertanyaan yang sering diajukan
Should I use this estimate or the motor nameplate?
Use the manufacturer’s nameplate current for final control and protection selection. This estimate helps when only shaft power, efficiency and power factor are available.
Are efficiency and power factor the same thing?
No. Efficiency compares shaft output with real electrical input. Power factor compares real with apparent AC power. A motor can have high efficiency and still draw reactive current.
Can I calculate starting current with this tool?
No. Starting current depends on motor design, starting method and supply conditions. Use manufacturer data for direct-on-line, star-delta, soft-starter or drive applications.
Is the estimate valid on the input side of a VFD?
Not as a drive-input calculation. Drive losses, harmonics and input power factor differ from the motor-terminal conditions used here. Check the drive manufacturer’s input-current data.
Perlu bantuan memilih produk CHAC?
Sertakan tegangan sistem, arus beban, dan kondisi pemasangan dalam pertanyaan Anda.
Contoh aplikasi · Masukan ilustratif
Estimating current for a 15 kW pump control panel
When preparing a pump control panel before the final motor nameplate is available, shaft power alone is not enough to estimate current. A 15 kW motor at 400 V three-phase, power factor 0.85 and 90% efficiency gives 28.30 A in this calculator. That estimate helps narrow the CHAC CQC6 contactor and CQR2 overload-relay data to review. It does not establish a complete starter combination. Once the motor is confirmed, use its actual nameplate current and starting duty to check the contactor ratings, overload range and short-circuit protection.
Data produk: Produsen Kontaktor AC Industri Seri CQC6 OEM · Relai beban berlebih Thermal CQR2 Series



