Máy tính lựa chọn tiếp điểm — AC-1 / AC-3
Đo dòng điện của bộ phận tiếp xúc AC và so sánh tải AC-3 ba pha với bảng dòng điện và công suất động cơ CHAC CQC6 ở mức điện áp 230, 400 hoặc 690 V.
Compare a three-phase AC-3 load with the published CQC6 current and motor-power columns. AC-1 gives a current reference for a separate datasheet check.
Kết quả
Danh sách rút gọn bảng AC-3
CQC6-25Chỉ đối sánh bảng; chưa xác minh sự phối hợp của bộ khởi động.CQC6-25 là mẫu sản phẩm đầu tiên được niêm yết, đáp ứng đồng thời các yêu cầu về dòng điện AC-3 và công suất động cơ ở mức 400 V.
I = Pshaft × 1,000 / (√3 × V × PF × η); so sánh AC-3 Ie và kW của động cơCQC6 đối sánh tham chiếu sử dụng cả cột dòng điện hiện tại đã công bố và cột kW ở điện áp đã chọn. Vui lòng xác nhận dòng điện ghi trên nhãn thực tế, điện áp cuộn dây, chế độ khởi động, tần suất đóng cắt và mức phối hợp trước khi đặt hàng.
Tại sao lại có kết quả như vậy?
Yêu cầu AC-3 Ie ≥ 20.75 A; công suất động cơ ≥ 11 kW. Dòng điện được ước tính dựa trên công suất trục, hệ số công suất và hiệu suất.
Tham chiếu được chọn và các tùy chọn liền kề đã được liệt kê. Các giá trị được làm tròn để hiển thị; các kiểm tra sử dụng giá trị chưa được làm tròn.
| Bộ phận tiếp nhận | AC-3 hiện tại | Công suất động cơ ở 400 V | Lý do |
|---|---|---|---|
| CQC6-18 | 18.00 A · Yêu cầu bên dưới | 7.5 kW · Yêu cầu bên dưới | AC-3 dòng điện hiện tại dưới mức yêu cầu; Công suất động cơ định mức dưới mức yêu cầu |
| CQC6-25Tham chiếu đã chọn | 25.00 A · Đáp ứng yêu cầu | 11 kW · Đáp ứng yêu cầu | Trận đấu đầu tiên được liệt kê cho các kiểm tra này |
| CQC6-32 | 32.00 A · Đáp ứng yêu cầu | 15 kW · Đáp ứng yêu cầu | Séc đã được thanh toán; tùy chọn sau đó được liệt kê |
Xem tất cả các tùy chọn đã được đánh dấu 12
| Bộ phận tiếp nhận | AC-3 hiện tại | Công suất động cơ ở 400 V | Lý do |
|---|---|---|---|
| CQC6-6 | 6.00 A · Yêu cầu bên dưới | 2.2 kW · Yêu cầu bên dưới | AC-3 dòng điện hiện tại dưới mức yêu cầu; Công suất động cơ định mức dưới mức yêu cầu |
| CQC6-9 | 9.00 A · Yêu cầu bên dưới | 4 kW · Yêu cầu bên dưới | AC-3 dòng điện hiện tại dưới mức yêu cầu; Công suất động cơ định mức dưới mức yêu cầu |
| CQC6-12 | 12.00 A · Yêu cầu bên dưới | 5.5 kW · Yêu cầu bên dưới | AC-3 dòng điện hiện tại dưới mức yêu cầu; Công suất động cơ định mức dưới mức yêu cầu |
| CQC6-18 | 18.00 A · Yêu cầu bên dưới | 7.5 kW · Yêu cầu bên dưới | AC-3 dòng điện hiện tại dưới mức yêu cầu; Công suất động cơ định mức dưới mức yêu cầu |
| CQC6-25Tham chiếu đã chọn | 25.00 A · Đáp ứng yêu cầu | 11 kW · Đáp ứng yêu cầu | Trận đấu đầu tiên được liệt kê cho các kiểm tra này |
| CQC6-32 | 32.00 A · Đáp ứng yêu cầu | 15 kW · Đáp ứng yêu cầu | Séc đã được thanh toán; tùy chọn sau đó được liệt kê |
| CQC6-38 | 38.00 A · Đáp ứng yêu cầu | 18.5 kW · Đáp ứng yêu cầu | Séc đã được thanh toán; tùy chọn sau đó được liệt kê |
| CQC6-40 | 40.00 A · Meets requirement | 18.5 kW · Đáp ứng yêu cầu | Séc đã được thanh toán; tùy chọn sau đó được liệt kê |
| CQC6-50 | 50.00 A · Meets requirement | 22 kW · Meets requirement | Séc đã được thanh toán; tùy chọn sau đó được liệt kê |
| CQC6-65 | 65.00 A · Meets requirement | 30 kW · Meets requirement | Séc đã được thanh toán; tùy chọn sau đó được liệt kê |
| CQC6-80 | 80.00 A · Meets requirement | 37 kW · Meets requirement | Séc đã được thanh toán; tùy chọn sau đó được liệt kê |
| CQC6-95 | 95.00 A · Meets requirement | 45 kW · Meets requirement | Séc đã được thanh toán; tùy chọn sau đó được liệt kê |
Vẫn chưa được xác nhận
- Confirm coil supply, actual nameplate data and switching duty.
- Ambient derating, endurance and short-circuit coordination have not been verified.
Nguồn dữ liệu: Bảng xếp hạng CHAC CQC6 AC-3 (Mở trong tab mới)
Công thức và phương pháp
Đo dòng điện của bộ phận tiếp xúc AC và so sánh tải AC-3 ba pha với bảng dòng điện và công suất động cơ CHAC CQC6 ở mức điện áp 230, 400 hoặc 690 V.
Cách sử dụng máy tính này
- Choose AC-3 for normal squirrel-cage motor starting/stopping, or AC-1 for a suitable non-inductive load.
- Use the stated line voltage and shaft power for AC-3. Enter actual nameplate current when available.
- Compare the table shortlist with the exact variant, control-coil voltage and required switching duty.
Giới hạn tính toán
Three-phase reference only. AC-4, reversing, plugging, frequent inching, capacitor switching, derating and tested starter coordination are not assessed. AC-1 gives a numeric Ie comparison without model selection.
Contactor sizing for AC-1 and AC-3 loads
A contactor’s AC-3 operating current depends on voltage and utilization duty. This tool reads the published CQC6 current and three-phase motor-kW columns at 230, 400 or 690 V. It checks both columns; a matching ampere value alone is insufficient.
Ghi chú nhập
| Input | Những điều cần kiểm tra |
|---|---|
| AC-3 or AC-1 | AC-3 uses shaft output and efficiency. AC-1 uses electrical input and gives an operational-current reference without selecting a model. |
| Nameplate current | A positive entry overrides the calculated current. The entered shaft kW still remains part of the AC-3 table check. |
| Voltage and allowance | Select the table’s line-voltage column. A user allowance changes the current reference; it is not a universal required margin. |
Ví dụ thực tế · giá trị dạng ban đầu
11 kW three-phase motor at 400 V
AC-3 · PF 0.85 · efficiency 90% · no current override · allowance 1.00
I = 11,000 / (√3 × 400 × 0.85 × 0.90) = 20.75 A
At 400 V, CQC6-25 lists AC-3 Ie 25 A and motor output 11 kW.
CQC6-25
This is the first loaded table row meeting both entered conditions. Confirm the actual motor nameplate, coil supply, switching rate and installation duty.
Contactor sizing: motor current, voltage and duty
Start with the motor nameplate current at the intended supply voltage. When only shaft output is known, estimate three-phase current as I = P × 1,000 / (√3 × V × PF × η), using efficiency η as a decimal. A lower power factor or efficiency increases the estimated current for the same shaft kW.
For an AC-3 shortlist, compare that current and the motor output with the same voltage column in the contactor table. At 400 V, an 11 kW motor in this example draws 20.75 A; CQC6-25 meets both the 25 A operational-current rating and the 11 kW motor rating. A current-only comparison would miss the second requirement.
AC-1 vs AC-3: choose the utilization category first
AC-1 covers non-inductive or slightly inductive loads, such as resistance heating. AC-3 applies to starting squirrel-cage motors and switching them off while running. These duties impose different making and breaking demands, so one contactor can have different ratings for each category.
For AC-1, compare the load with an operational Ie rating explicitly declared for the application. Conventional thermal current Ith describes a different test condition. This calculator does not turn an Ith value into an AC-1 model recommendation.
An AC contactor’s coil voltage is a separate choice
The main contacts carry the load; the coil belongs to the control circuit. A 400 V motor supply does not by itself specify the coil voltage. Check the available control supply, AC or DC coil type, frequency where applicable, auxiliary contacts and mounting arrangement.
Use the model result to open the CQC6 technical data and complete those checks. Frequent jogging, plugging, reversing or capacitor switching needs its own duty assessment rather than the normal AC-3 selection used here.
What the table match does not decide
- Conventional thermal current Ith is not interchangeable with operational current Ie. The published AC-1-labelled thermal row is deliberately not used to choose AC-1 models.
- Starting/stopping duty, AC-4 operation, electrical endurance, ambient derating and short-circuit coordination still require the exact product instructions.
Các câu hỏi thường gặp
Why can the same contactor have a lower current at 690 V?
Operational current is voltage- and duty-specific. The CQC6 table lists separate AC-3 columns; the calculator does not carry a 400 V current value into the 690 V column.
Does AC-3 cover reversing or frequent inching?
Do not assume so. Plugging, inching and some reversing duties require a different utilization assessment. This tool is limited to normal AC-3 motor starting and stopping.
Can I enter the actual motor current?
Yes. Enter a positive nameplate current to replace the power-based estimate. Keep the correct shaft kW so the motor-power column is also checked.
Why is there no AC-1 model result?
The available source row is conventional free-air thermal current. The tool instead compares your current with an entered, independently verified AC-1 operational Ie.
What is a contactor used for in a motor circuit?
A contactor switches the motor supply through electrically operated main contacts. Its coil is controlled by the control circuit. It does not replace the overload relay or the short-circuit protective device.
Does the motor voltage determine the contactor coil voltage?
No. Main-circuit voltage and coil supply are separate specifications. Check the actual control voltage, coil type and frequency where applicable when ordering the selected contactor.
Cần giúp đỡ trong việc lựa chọn sản phẩm CHAC?
Hãy gửi hệ số điện áp, dòng tải và điều kiện lắp đặt của hệ thống cùng với yêu cầu của bạn.
CQC6 AC contactor ratings
Published AC-3 operational current and controlled three-phase squirrel-cage motor power. The voltage groups below retain the labels used in the CHAC product table.
Reference data. Calculate to highlight the matching row.
Scroll horizontally on small screens to read all columns.
| Số hiệu mô hình | 220V/230V | 380V/400V | 660V/690V | |||
|---|---|---|---|---|---|---|
| AC-3 Ie (A) | Motor power (kW) | AC-3 Ie (A) | Motor power (kW) | AC-3 Ie (A) | Motor power (kW) | |
| CQC6 -6Current reference | 6 | 1.5 | 6 | 2.2 | 4.8 | 3 |
| CQC6 -9Current reference | 9 | 2 | 9 | 4 | 6.6 | 5.5 |
| CQC6 -12Current reference | 12 | 3.5 | 12 | 5.5 | 8.9 | 7.5 |
| CQC6 -18Current reference | 18 | 4 | 18 | 7.5 | 12 | 10 |
| CQC6 -25Current reference | 25 | 6 | 25 | 11 | 18 | 15 |
| CQC6 -32Current reference | 32 | 7.5 | 32 | 15 | 20.2 | 18.5 |
| CQC6 -38Current reference | 38 | 9 | 38 | 18.5 | 20.2 | 18.5 |
| CQC6 -40Current reference | 40 | 11 | 40 | 18.5 | 34 | 30 |
| CQC6 -50Current reference | 50 | 15 | 50 | 22 | 39 | 33 |
| CQC6 -65Current reference | 65 | 18.5 | 65 | 30 | 42 | 37 |
| CQC6 -80Current reference | 80 | 22 | 80 | 37 | 49 | 45 |
| CQC6 -95Current reference | 95 | 25 | 95 | 45 | 49 | 45 |
Reading this reference
- The calculator uses the 230, 400 or 690 V selection within the corresponding published voltage group.
- This table covers AC-3 only. The separate conventional free-air thermal current row is not an AC-1 operational Ie selection table.
- Confirm the exact coil supply, switching duty and installation conditions in the product documentation.
Source: CHAC CQC6 product technical table (Mở trong tab mới)
Source checked: . This is the retrieval date, not a standard edition or product revision date.
Ví dụ ứng dụng · Các thông tin minh họa
Matching a 15 kW motor to both CQC6 AC-3 columns
For a pump-control example, enter 15 kW shaft output, 400 V, AC-3 duty and an illustrative 28 A nameplate current, with no added current allowance. The calculator shortlists CQC6-32: the CHAC table lists 32 A and 15 kW in the 380V/400V group. CQC6-25 is below both requirements at 25 A and 11 kW. This is why checking only the model’s ampere value can be misleading. Use the table match to continue the selection, then confirm the coil supply, switching duty, installation conditions and required protection for the actual motor circuit.
Thông tin sản phẩm: Nhà sản xuất thiết bị tiếp xúc AC công nghiệp dòng CQC6


