PXB6LE-63 Dispositivo de desconexión electrónico de corriente residual con protección contra sobrecorriente
El RCBO electrónico CHAC PXB6LE-63 combina la protección contra sobrecargas, cortocircuitos y corrientes residuales en un solo dispositivo. Elija entre cuatro configuraciones de polos, curvas B/C/D y sensibilidades de tipo AC/A para adaptarse al circuito, con corrientes nominales desde 6A hasta 63A.
Descripción del producto
El CHAC PXB6LE-63 RCBO electrónico Combina protección contra sobrecorriente y contra corriente residual. Seleccione la detección de tipo AC o tipo A, la sensibilidad de corriente residual requerida y una curva de sobrecorriente B/C/D como detalles de pedido independientes.
Para importadores, distribuidores y fabricantes de equipos, CHAC puede revisar la configuración solicitada en función de los requisitos del circuito y de la documentación del mercado de destino. Acuerde el modelo exacto, los planos y los requisitos de marcado antes de la aprobación de la muestra o de realizar un pedido repetido.
Puntos clave de selección
Aplicaciones típicas
Consider PXB6LE-63 for AC final circuits that require both earth-leakage and overcurrent protection. Type selection depends on load electronics, expected fault waveforms and the installation rules; the highest current or sensitivity value is not automatically the right choice.
Guía de Solicitudes y Selección
| Elemento de selección | PXB6LE-63 configuration | Qué verificar |
|---|---|---|
| Corriente nominal | 6–63A | Match the load and conductor ampacity, including enclosure temperature and grouping. |
| Poles and voltage | 1P+N / 2P: 240V AC; 3P+N / 4P: 415V AC | Confirm the required neutral-switching and protection arrangement. |
| Protección contra la corriente residual | Type AC or A; 10/30/50/100/300mA | Specify detection type and sensitivity independently from rated current. |
| Overcurrent characteristic | B/C/D; listed Ics 6000A | Coordinate inrush and fault level rather than changing curve solely to avoid trips. |
Use these checks to compare the protection function, configuration and related CHAC products before specifying PXB6LE-63. Related products are selection alternatives or system components, not automatic replacements.
Specify the leakage type separately from the trip curve
Type A describes the residual-current waveform coverage; a C curve describes the overcurrent trip characteristic.
Investigate leakage before increasing sensitivity settings
Repeated residual-current trips may come from insulation defects, accumulated equipment leakage or wiring errors.
Compare PXB6Ln-40 for the required function
El RCBO electrónico CHAC PXB6Ln-40 combina la protección contra sobrecorriente y corriente residual en una configuración compacta de 1P+N. Ofrece clasificaciones de 6–40A, curvas B/C y opciones de tipo AC/A para circuitos que operan a 230/240V CA.
Compare PXB6LE-63B for the required function
El CHAC PXB6LE-63B es un disipador de corriente eléctrica electrónico que combina la protección contra sobrecargas y cortocircuitos con la protección contra la corriente residual de tipo B. Disponible en rangos de amperaje de 6 a 63 A y configuraciones de cuatro polos, ofrece curvas B/C/D y sensibilidades a la corriente residual de 30 mA a 300 mA.
Need Help Specifying PXB6LE-63?
Send the circuit requirements, selected configuration, destination market and quantity for a model-specific review.
Specify the leakage type separately from the trip curve
Type A describes the residual-current waveform coverage; a C curve describes the overcurrent trip characteristic. An order such as Type A, C curve still needs a rated current, sensitivity and pole arrangement. Keeping these fields separate prevents ambiguous distributor orders.
Investigate leakage before increasing sensitivity settings
Repeated residual-current trips may come from insulation defects, accumulated equipment leakage or wiring errors. A higher mA threshold is not a routine cure. Have the circuit assessed and select protection that still meets the application and local requirements.
How to Specify a PXB6LE-63 Order
Use the configuration details below in the purchase specification. Keep the approved drawing revision and product identification with the order so repeat deliveries can be checked consistently.
| Detalle de la orden | Information to include |
|---|---|
| Corriente nominal | 6–63A — Match the load and conductor ampacity, including enclosure temperature and grouping. |
| Poles and voltage | 1P+N / 2P: 240V AC; 3P+N / 4P: 415V AC — Confirm the required neutral-switching and protection arrangement. |
| Protección contra la corriente residual | Type AC or A; 10/30/50/100/300mA — Specify detection type and sensitivity independently from rated current. |
| Overcurrent characteristic | B/C/D; listed Ics 6000A — Coordinate inrush and fault level rather than changing curve solely to avoid trips. |
| Project and documents | Supply the application, installation conditions and destination-market document requirements. |
| Quantity and identification | State the quantity, sample requirement, packaging language and any proposed branding; confirm feasibility before approval. |
Check Installation Fit Before Approval
Especificaciones técnicas
| Parámetro | |
| Tensión nominal (V) | 240V~(1P+N、2P)/415V~(3P+N、4P) |
| Corriente Nominal (A) | 6、10、16、20、25、32、40、50、63 |
| Número de polos | 1P+N、2P、3P+N、4P |
| Rated Short-Circuit Breaking Capacity Ics(A) | 6000A |
| Rated Residual Operating Current IΔn(mA) | 10、30、50、100、300 |
| Rated Residual Non-Operating Current IΔno(mA) | 0.5IΔn |
| Rated Residual Make and Break Capacity IΔm(A) | 3000A |
| Residual Current Tripping Threshold | ≤0,1s |
| Residual Current Trip Type | AC Type、A Type |
| Resistencia Mecánica | ≥6000 |
| Resistencia eléctrica | ≥4000 |
| Curvas de disparo | B, C, D |
| Grado de contaminación | 2 |
| Clase de Protección | IP 20 |
| Categoría de instalación | Ⅲ |
| Estándares | IEC61009-1, GB/T16917.1 |
| Certificación | CE CB CCC|DEKRA Certified |
Tripping Characteristics (Reference Temperature: 30℃)
| Artículo | Curva de disparo | Corriente de prueba (A) | Estado inicial | Límite de tiempo para disparar o no disparar | Resultado esperado | Observaciones |
| Retraso | ≤63 | Frío | 1.13En | ≤1 h | No desatascador | |
| Retraso | ≤63 | Siguiendo con la prueba anterior | 1.45pulg | ＜1h | Tropezando | La corriente aumenta de forma gradual hasta alcanzar el valor especificado en 5 segundos. |
| Retraso | ≤32 | Frío | 2.55In | 1＜t＜60s | Tropezando | |
| Retraso | >32 | Frío | 2.55In | 1＜t＜120s | Tropezando | |
| Instantáneo | Cualquier valor | Frío | 3、5、10In | ≤0,1s | No desatascador | B, C, D |
| Instantáneo | Cualquier valor | Frío | 5、10、20In | ＜0.1s | Tropezando | B, C, D |
Nota: El término “en frío” significa que la prueba se realiza a una temperatura de calibración de referencia sin carga antes de la prueba.
Requisitos del conductor y sección transversal
| Sección transversal de cobre (mm²) | Corriente nominal In(A) |
| 1 | En≤6 |
| 1.5 | 6＜En≤13 |
| 2.5 | 13＜En ≤20 |
| 4 | 20＜In≤25 |
| 6 | 25<En≤32 |
| 10 | 32＜En≤50 |
| 16 | 50＜In≤63 |
Designación del tipo
Curvas de disparo
Dimensiones(mm)
¿Por qué elegir CHAC?
CHAC Electric supplies electrical protection and control products for importers, distributors and equipment brands. For PXB6LE-63, agree the configuration, technical documents, approved sample and identification requirements before production. The company facilities shown below provide company context, not a claim that every model uses the same production or test process.
01
CONFÍRMESE LA ESPECIFICACIÓN
Agree the PXB6LE-63 configuration, circuit duty and installation requirements.
02
LEER LOS DOCUMENTOS
Compruebe los dibujos específicos del modelo y los requisitos del mercado de destino.
03
APROBAR LA MUESTRA
Registre los requisitos de configuración y marcado aceptados.
04
Definir comprobaciones de orden
Acepto los requisitos de embalaje, identificación y entrega en la cotización.
Línea de ensamblaje automatizada
Laboratorio de pruebas
Inyección y Estampado
Inspección de calidad
¿Qué podemos personalizar?
Discuss PXB6LE-63 product identification, packaging and documentation with CHAC. Each proposed change is subject to technical feasibility, marking rules and approval of the exact order; no altered rating or certification is implied.
Logotipo y marca
Envíe el diseño del logotipo y los requisitos de marcado para su revisión en función del área de impresión disponible y las marcaciones obligatorias del producto.
Embalaje y manuales
Defina los requisitos de etiquetas de cartón, idioma de embalaje, identificación del producto e instrucciones para el mercado de destino.
Selección de configuración
Specify PXB6LE-63 with the required rated current, operating conditions and protection duty. Confirm the complete order combination.
Assembly Requirements
Provide the mounting and connection requirements for review. Changes to the housing, terminals or operating arrangement require engineering approval.
Documentación del mercado
Request documents covering the exact PXB6LE-63 model and destination market. A standard reference alone is not evidence of certification.
Aprobación de la muestra
Acordar la especificación del producto, la revisión del dibujo y los criterios de aceptación antes de confirmar un pedido de producción.
Documentación técnica y soporte
PXB6LE-63 Technical Documents
Request the PXB6LE-63 datasheet, configuration drawing, installation instructions and available model-specific market documents.Solicitud de hoja de datos
¿Necesita documentos técnicos?
Send the application, electrical requirements, assembly layout and destination market for configuration and document review.Contáctanos
PXB6LE-63 Product FAQ
What is the difference between Type A and Type AC RCBOs?
Type AC is intended for sinusoidal AC residual currents, while Type A also covers specified pulsating DC residual currents. PXB6LE-63 offers both options. Select for the connected equipment and local rules, not simply the lower purchase price.
Does a Type A RCBO mean it has a B or C tripping curve?
No. Residual-current type and overcurrent curve are separate specifications. PXB6LE-63 offers Type AC/A detection with B/C/D curves; state both in the order.
Is a 100mA RCBO a direct substitute for a 30mA RCBO?
Not automatically. The sensitivity changes the residual-current protection level and may no longer satisfy the circuit requirements. Confirm the application and local rules before substituting any sensitivity.
How should I choose the PXB6LE-63 residual-current sensitivity?
Select the mA rating from the circuit purpose, equipment instructions and local requirements. Rated current in amperes is a separate specification. Confirm the exact PXB6LE-63 sensitivity variant and its operating-time data rather than using a larger threshold to mask recurring trips.
Why can a PXB6LE-63 installation trip repeatedly?
Possible causes include insulation faults, accumulated equipment leakage, incorrect neutral connections or an unsuitable protection type. Have a qualified person investigate the circuit and follow the device test instructions before changing the rating or replacing protection.
What should an importer include in a PXB6LE-63 inquiry?
Specify poles, AC supply, rated current, residual-current type and sensitivity, plus the overcurrent curve if ordering an RCBO. Add the destination market, required documents, quantity and marking requirements so the quotation identifies the exact configuration.
Specify the Right PXB6LE-63 Configuration
Send CHAC your required configuration, application, destination market and estimated quantity. We will review the requested specification and provide the relevant technical documents and commercial proposal.
