حاسبة اختيار المكونات — AC-1 / AC-3
احسب تيار المكونات الكهربائية المتصلة بالكمبيوتر، واقارن أحمال التيار ثلاثي الطور AC-3 مع جداول تيار CHAC CQC6 ومحرك الكيلووات عند 230 أو 400 أو 690 فولت.
قارن حمل ثلاثي الأطوار AC-3 مع أعمدة التيار وقوة المحرك المنشورة CQC6. يوفر AC-1 مرجعًا للتيار لإجراء فحص منفصل في ورقة البيانات.
النتيجة
قائمة مختصرة لطاولة AC-3
CQC6-25مطابقة الجدول فقط؛ لم يتم التحقق من تنسيق المُبتدئCQC6-25 هو النموذج الأول المدرج الذي يستوفي كلاً من متطلبات التيار AC-3 وطاقة المحرك عند 400 فولت.
I = Pshaft × 1,000 / (√3 × V × PF × η); قارن بين AC-3 Ie وقوة المحرك بالكيلوواطيستخدم مطابق المرجع CQC6 كلاً من أعمدة التيار المُعلَّن الحالي والكيلوواط عند الجهد المحدد. يُرجى التأكد من التيار الفعلي على اللوحة، وجهد الملف، وواجب التشغيل، ومعدل التبديل، والتنسيق قبل الطلب.
لماذا هذا النتيجة؟
مطلوب AC-3 Ie ≥ 20.75 A؛ تصنيف المحرك ≥ 11 كيلوواط. يتم تقدير التيار من قوة العمود، ومعامل القدرة والكفاءة.
خيارات مرجعية محددة وخيارات مدرجة مجاورة. يتم تقريب القيم للعرض؛ وتستخدم التحققات القيم غير المدورة.
| الموصل | AC-3 الحالي | خرج المحرك عند 400 فولت | السبب |
|---|---|---|---|
| CQC6-18 | 18.00 A · المتطلب أدناه | 7.5 كيلوواط · تحت المتطلبات | AC-3 التيار الحالي أقل من المطلوب؛ تصنيف قوة المحرك أقل من المطلوب |
| CQC6-25مرجع مختار | 25.00 A · يلبي المتطلبات | 11 كيلو واط · يلبي المتطلبات | أول مباراة مدرجة لهذه الفحوصات |
| CQC6-32 | 32.00 أ · يلبي المتطلبات | 15 كيلو واط · يلبي المتطلبات | تم استيفاء الشيكات؛ الخيار مدرج لاحقًا |
عرض جميع الخيارات المحددة في 12
| الموصل | AC-3 الحالي | خرج المحرك عند 400 فولت | السبب |
|---|---|---|---|
| CQC6-6 | 6.00 A · المتطلب أدناه | 2.2 كيلوواط · المتطلب أدناه | AC-3 التيار الحالي أقل من المطلوب؛ تصنيف قوة المحرك أقل من المطلوب |
| CQC6-9 | 9.00 A · المتطلب أدناه | 4 كيلوواط · تحت المتطلب | AC-3 التيار الحالي أقل من المطلوب؛ تصنيف قوة المحرك أقل من المطلوب |
| CQC6-12 | 12.00 A · المتطلب التالي | 5.5 كيلوواط · تحت المتطلبات | AC-3 التيار الحالي أقل من المطلوب؛ تصنيف قوة المحرك أقل من المطلوب |
| CQC6-18 | 18.00 A · المتطلب أدناه | 7.5 كيلوواط · تحت المتطلبات | AC-3 التيار الحالي أقل من المطلوب؛ تصنيف قوة المحرك أقل من المطلوب |
| CQC6-25مرجع مختار | 25.00 A · يلبي المتطلبات | 11 كيلو واط · يلبي المتطلبات | أول مباراة مدرجة لهذه الفحوصات |
| CQC6-32 | 32.00 أ · يلبي المتطلبات | 15 كيلو واط · يلبي المتطلبات | تم استيفاء الشيكات؛ الخيار مدرج لاحقًا |
| CQC6-38 | 38.00 أ · يلبي المتطلبات | 18.5 كيلو واط · يلبي المتطلبات | تم استيفاء الشيكات؛ الخيار مدرج لاحقًا |
| CQC6-40 | 40.00 أ · يلبي المتطلب | 18.5 كيلو واط · يلبي المتطلبات | تم استيفاء الشيكات؛ الخيار مدرج لاحقًا |
| CQC6-50 | 50.00 A · يلبي المتطلبات | 22 كيلو واط · يلبي المتطلبات | تم استيفاء الشيكات؛ الخيار مدرج لاحقًا |
| CQC6-65 | 65.00 أ · يلبي المتطلبات | 30 كيلو واط · يلبي المتطلبات | تم استيفاء الشيكات؛ الخيار مدرج لاحقًا |
| CQC6-80 | 80.00 A · يلبي المتطلبات | 37 كيلو واط · يلبي المتطلبات | تم استيفاء الشيكات؛ الخيار مدرج لاحقًا |
| CQC6-95 | 95.00 A · يلبي المتطلبات | 45 كيلو واط · يلبي المتطلبات | تم استيفاء الشيكات؛ الخيار مدرج لاحقًا |
لا يزال قيد التأكيد
- يُرجى التأكد من مصدر تغذية الملف، والبيانات الفعلية المدونة على اللوحة التعريفية، وطبيعة حمل التبديل.
- لم يتم التحقق من تخفيض القدرة في ظروف البيئة المحيطة، ومن العمر الافتراضي، ومن تنسيق الدوائر القصيرة.
مصدر البيانات: جدول تقييم CHAC CQC6 AC-3 (ينفتح في علامة تبويب جديدة)
الخوارزمية والطريقة
احسب تيار المكونات الكهربائية المتصلة بالكمبيوتر، واقارن أحمال التيار ثلاثي الطور AC-3 مع جداول تيار CHAC CQC6 ومحرك الكيلووات عند 230 أو 400 أو 690 فولت.
كيفية استخدام هذه الحاسبة
- اختر AC-3 لبدء/إيقاف المحرك العادي ذي القفص السنجابي، أو AC-1 للحمل غير الحثي المناسب.
- استخدم جهد الخط المحدد وقوة العمود لـ AC-3. أدخل التيار الفعلي على اللوحة التعريفية عند توفره.
- قارن القائمة المختصرة للجداول مع الطراز الدقيق، وجهد ملف التحكم، وواجب التبديل المطلوب.
حدود الحساب
مرجع ثلاثي الطور فقط. لا يتم تقييم AC-4، أو العكس، أو التوصيل المفاجئ، أو التحرك المتكرر بخطوات صغيرة، أو تبديل المكثفات، أو تخفيض القدرة، أو تنسيق المشغل المختبر. يوفر AC-1 مقارنة رقمية لـ Ie دون اختيار النموذج.
تحديد حجم المُقَطِّع للحمولات AC-1 وAC-3
يعتمد التيار التشغيلي لقاطع الدائرة AC-3 على الجهد ودرجة الاستخدام. تقرأ هذه الأداة قيم التيار المنشورة في عمودي التيار CQC6 وقوة المحرك ثلاثي الطور بالكيلوواط عند جهدين 230 و400 أو 690 فولت. وهي تتحقق من كلا العمودين؛ فالقيمة المطابقة للأمبير وحدها غير كافية.
تدوين الملاحظات
| مدخل | ما الذي يجب التحقق منه |
|---|---|
| AC-3 أو AC-1 | AC-3 uses shaft output and efficiency. AC-1 uses electrical input and gives an operational-current reference without selecting a model. |
| Nameplate current | A positive entry overrides the calculated current. The entered shaft kW still remains part of the AC-3 table check. |
| Voltage and allowance | Select the table’s line-voltage column. A user allowance changes the current reference; it is not a universal required margin. |
مثال عملي · قيم النموذج الأولي
11 kW three-phase motor at 400 V
AC-3 · PF 0.85 · efficiency 90% · no current override · allowance 1.00
I = 11,000 / (√3 × 400 × 0.85 × 0.90) = 20.75 A
At 400 V, CQC6-25 lists AC-3 Ie 25 A and motor output 11 kW.
CQC6-25
This is the first loaded table row meeting both entered conditions. Confirm the actual motor nameplate, coil supply, switching rate and installation duty.
Contactor sizing: motor current, voltage and duty
Start with the motor nameplate current at the intended supply voltage. When only shaft output is known, estimate three-phase current as I = P × 1,000 / (√3 × V × PF × η), using efficiency η as a decimal. A lower power factor or efficiency increases the estimated current for the same shaft kW.
For an AC-3 shortlist, compare that current and the motor output with the same voltage column in the contactor table. At 400 V, an 11 kW motor in this example draws 20.75 A; CQC6-25 meets both the 25 A operational-current rating and the 11 kW motor rating. A current-only comparison would miss the second requirement.
AC-1 vs AC-3: choose the utilization category first
AC-1 covers non-inductive or slightly inductive loads, such as resistance heating. AC-3 applies to starting squirrel-cage motors and switching them off while running. These duties impose different making and breaking demands, so one contactor can have different ratings for each category.
For AC-1, compare the load with an operational Ie rating explicitly declared for the application. Conventional thermal current Ith describes a different test condition. This calculator does not turn an Ith value into an AC-1 model recommendation.
An AC contactor’s coil voltage is a separate choice
The main contacts carry the load; the coil belongs to the control circuit. A 400 V motor supply does not by itself specify the coil voltage. Check the available control supply, AC or DC coil type, frequency where applicable, auxiliary contacts and mounting arrangement.
Use the model result to open the CQC6 technical data and complete those checks. Frequent jogging, plugging, reversing or capacitor switching needs its own duty assessment rather than the normal AC-3 selection used here.
What the table match does not decide
- Conventional thermal current Ith is not interchangeable with operational current Ie. The published AC-1-labelled thermal row is deliberately not used to choose AC-1 models.
- Starting/stopping duty, AC-4 operation, electrical endurance, ambient derating and short-circuit coordination still require the exact product instructions.
الأسئلة الشائعة
Why can the same contactor have a lower current at 690 V?
Operational current is voltage- and duty-specific. The CQC6 table lists separate AC-3 columns; the calculator does not carry a 400 V current value into the 690 V column.
Does AC-3 cover reversing or frequent inching?
Do not assume so. Plugging, inching and some reversing duties require a different utilization assessment. This tool is limited to normal AC-3 motor starting and stopping.
Can I enter the actual motor current?
Yes. Enter a positive nameplate current to replace the power-based estimate. Keep the correct shaft kW so the motor-power column is also checked.
Why is there no AC-1 model result?
The available source row is conventional free-air thermal current. The tool instead compares your current with an entered, independently verified AC-1 operational Ie.
What is a contactor used for in a motor circuit?
A contactor switches the motor supply through electrically operated main contacts. Its coil is controlled by the control circuit. It does not replace the overload relay or the short-circuit protective device.
Does the motor voltage determine the contactor coil voltage?
No. Main-circuit voltage and coil supply are separate specifications. Check the actual control voltage, coil type and frequency where applicable when ordering the selected contactor.
هل تحتاج إلى مساعدة في اختيار منتج CHAC؟
ارسل إلى النظام طاقة التيار الكهربائي والجهد الكهربائي وظروف التركيب الخاصة بك مع استفسارك.
CQC6 AC contactor ratings
Published AC-3 operational current and controlled three-phase squirrel-cage motor power. The voltage groups below retain the labels used in the CHAC product table.
Reference data. Calculate to highlight the matching row.
Scroll horizontally on small screens to read all columns.
| رقم النموذج | 220V/230V | 380V/400V | 660V/690V | |||
|---|---|---|---|---|---|---|
| AC-3 Ie (A) | Motor power (kW) | AC-3 Ie (A) | Motor power (kW) | AC-3 Ie (A) | Motor power (kW) | |
| CQC6 -6Current reference | 6 | 1.5 | 6 | 2.2 | 4.8 | 3 |
| CQC6 -9Current reference | 9 | 2 | 9 | 4 | 6.6 | 5.5 |
| CQC6 -12Current reference | 12 | 3.5 | 12 | 5.5 | 8.9 | 7.5 |
| CQC6 -18Current reference | 18 | 4 | 18 | 7.5 | 12 | 10 |
| CQC6 -25Current reference | 25 | 6 | 25 | 11 | 18 | 15 |
| CQC6 -32Current reference | 32 | 7.5 | 32 | 15 | 20.2 | 18.5 |
| CQC6 -38Current reference | 38 | 9 | 38 | 18.5 | 20.2 | 18.5 |
| CQC6 -40Current reference | 40 | 11 | 40 | 18.5 | 34 | 30 |
| CQC6 -50Current reference | 50 | 15 | 50 | 22 | 39 | 33 |
| CQC6 -65Current reference | 65 | 18.5 | 65 | 30 | 42 | 37 |
| CQC6 -80Current reference | 80 | 22 | 80 | 37 | 49 | 45 |
| CQC6 -95Current reference | 95 | 25 | 95 | 45 | 49 | 45 |
Reading this reference
- The calculator uses the 230, 400 or 690 V selection within the corresponding published voltage group.
- This table covers AC-3 only. The separate conventional free-air thermal current row is not an AC-1 operational Ie selection table.
- Confirm the exact coil supply, switching duty and installation conditions in the product documentation.
Source: CHAC CQC6 product technical table (ينفتح في علامة تبويب جديدة)
Source checked: . This is the retrieval date, not a standard edition or product revision date.
مثال على التطبيق • مدخلات إيضاحية
Matching a 15 kW motor to both CQC6 AC-3 columns
For a pump-control example, enter 15 kW shaft output, 400 V, AC-3 duty and an illustrative 28 A nameplate current, with no added current allowance. The calculator shortlists CQC6-32: the CHAC table lists 32 A and 15 kW in the 380V/400V group. CQC6-25 is below both requirements at 25 A and 11 kW. This is why checking only the model’s ampere value can be misleading. Use the table match to continue the selection, then confirm the coil supply, switching duty, installation conditions and required protection for the actual motor circuit.
بيانات المنتج: مصنع OEM لموصلات التيار المتردد الصناعية من سلسلة CQC6


